background image

Installation instructions KC 906.2 USA

3

The following symbols are used in this installation manual:

[

The warning triangle will alert you about possible health risks or things 
that can cause potential damage to your appliance.

F

You’ll find useful hints and information when you see this symbol.

Safety instructions

■ 

Turn off the power source before installing the cooking surface.

■ 

Don’t operate the appliance until it has been properly installed within 
cabinetry or into an opening in the countertop!

■ 

Only qualified personnel should perform installations and repairs on 
electrical appliances. Do not repair or replace any part of the appliance 
unless specifically recommended in this manual. Do not put your safety 
at risk.

■ 

The glass ceramic surface is very tough and can easily withstand 
light to medium blows and loads distributed over large areas. You 
should avoid dropping concentrated loads like spice bottles onto the 
surface. The impact of such items can damage the cooking surface.

■ 

If the cooking surface becomes fractured or cracked, quit using it 
immediately. Disconnect the power source and call Customer 
Service.

■ 

The connecting cable must not come in contact with the hot cooking 
surface.

■ 

If the cooking center is not installed properly, there is a risk of tipping 
it over! Be sure it is fastened to the supporting rails.

■ 

WARNING! The adjacent side walls must be secured so the installed 
cooking center can’t tilt.

Installation conditions

■ 

Make sure the plastic finish or the veneer of the built-in kitchen furniture 
has a heat-resistant adhesive (100 °C/210 °F).

■ 

The appliance must be perfectly horizontal.

■ 

The cooking center must be installed between two side cabinets.

■ 

Make sure all components surrounding the oven can resist temperatures of 
at least 100 °C/210 °F. These include varnishes, edge bands, plastic 
surfaces, adhesives and paints. The adjacent cabinet fronts should be able 
to resist temperatures up to 70 °C/160 °F.

■ 

To eliminate the risk of burns or fire by reaching above heated surface units, 
do not put cabinet storage space above the surface units. If you do decide 
to put cabinet storage above the surface units, install a range hood that 
projects at least 5" horizontally beyond the bottom of the cabinets.

Installation dimensions

Distances

Concerning A*: 

A = 30" minimum clearance between the top of the cooking

suface and the bottom of an unprotected wood or metal cabinet or A = 24"
minimum when bottom of wood or metal cabinet is protected by not less than
1/4-inch-thick flame-retardant millboard covered with not less than No. 28
MSG sheet steel, 0.015-inch-thick stainless steel, 0.024-inch-thick
aluminium, or 0.020-inch-thick copper.
Hoods above the cook top should be at least 650 mm (26") above the cook
top.

Concerning B*:

 Minimum distance corresponds to the width of the

appliance.
To eliminate the risk of burns or fire by reaching over heated surface units,
do not put cabinet storage space above the surface units. If you do decide
to put cabinet storage above the surface untis, install a range hood that
projects at least 5" horizontally beyond the bottom of the cabinets.

Concerning C*:

This appliance can be mounted with two sides to a wall or

the side of a cabinet with a distance of at least 40 mm (1-9/16"). The third
side may only be positioned next to an appliance of equal height.
There should be a horizontal distance between the appliance and mounted
cupboards of at least 300 mm (12")  for ergonomical reasons.

Содержание KC 906.2









Отзывы: