background image

23

H4-72-02-03

For internal use only

10.

Troubleshooting

Note!

If the bulb for the interior lighting goes, the appliance can still be readily used. Contact an

authorised customer service office

 to replace the bulb.

Fault

Cause / Remedy

The appliance does not work.

• The door is not properly closed.

• The plug is not properly inserted into the

socket outlet.

• There is no electricity in the socket outlet.

(Check the house fuse.)

Condensation on the cooking surface, inside the 
cavity or near the door.

• If food containing water is cooked, it is com-

pletely normal for the steam which forms
inside the appliance to precipitate in the cav-
ity, on the cooking surface or on the door
frame as condensation.

Sparking in the appliance.

• In the modes with microwaves and in combi-

nation mode, do not operate the appliance
without food.

• In the above-mentioned modes do not use

any metal containers, bags or packing with
metal clips for cooking.

The food does not heat up and is not cooked 
through.

• Select the correct cooking function  or

increase the cooking time.

• The food was not completely thawed out

before the cooking process.

The food burns.

• Select the correct cooking function or reduce

the cooking time.

The food is not cooked evenly.

• Stir the food during the cooking process.

• Note that the food cooks better when it has

been cut into pieces of the same size.

Содержание EMWK 9600.0




























Отзывы: