Kuppersberg GS 6020, Технический паспорт

Страница: 5 / 34

8 9
TECHNICAL PASSPORT ENGLISH ENGLISH TECHNICAL PASSPORT
Dishwasher Dishwasher
B. Loading the Salt into
the Softener
Always use saltintended for use with
dishwasher.
NOTE: If your model has no water
softener, you may skip this section
WATER SOFTENER
The hardness of the water varies
from place to place. If hard water is
used in the dishwasher, deposits will
form onthe dishes andutensils.
The appliance isequipped with
aspecial softener thatuses salts
specifi cally designed to eliminatelime
and mineralsfrom the water.
The salt container is located beneath
the lower basket and should be fi lled as
follows:
Attention!
Only use salt specifi cally designed
for use in dishwashers! All other types
of salt not specifi cally designed for
use in a dishwasher, especially table
salt, will damage the water softener. In
case of damages caused by the use of
unsuitable salt the manufacturer does
not give any warranty nor is liable for
any caused damages.
Only fi ll with salt just before
starting one of the complete washing
programmes.
This will prevent any grains of salt
or salty water, which may have been
split, remaining on the bottom of the
machine for any period of time, which
may cause corrosion.
After the fi rst wash cycle the control
panel light expires.
A. Remove the lower basket and
then unscrew and remove the cap from
the salt container.
1
B. If you are fi lling the container for
the fi rst time, fi ll 2/3 of its volume with
water (around 500ml).
2
C. Place the end of the funnel
(supplied) into the hole and introduce
about 1,2kg of salt. It is normal for a
small amount of water to come out of
the salt container.
D. Carefully screw the cap back on.
E. Usually, the salt warning light will
be off in 2-6 days after the salt container
is fi lled with salt.
NOTE:
1. The salt container must be refi lled
when the salt warning light in the
control panel comes on. Though
the salt container is fi lled enough,
the indicator light may not black
out before the salt fully dissolve. If
there is no salt warning light in the
control panel (for some models),
you can judge when to load the salt
into the softener by the cycles that
the dishwasher had run (see the
following schema).
2. If there are spills of the salt, a Pre-
rinse program could be run to wipe
them out.
C. Fill the Rinse Aid Dispenser
Function of Rinse Aid
Rinse aid is automatically added
during the last rinse, ensuring thorough
rinsing, spot and streak free drying.
Attention!
Only use branded rinse aid for
dishwasher. Never fi ll the rinse aid
dispenser with any other substances
(e.g. dishwasher cleaning agent, liquid
detergent). This would damage the
appliance.
When to Refi ll the Rinse Aid
Dispenser
If there is no rinse-aid warning light
on the control panel, you can judge the
amount of rinse-aid by the color of the
optical level indicator «D» located next
to the cap. When the rinse-aid container
is full the whole indicator will be dark
.As the rinse aid diminishes, the size
of the dark dot decreases. You should
never let the rinse aid get below 1/4
full.
As the rinse aid diminishes, the size
of the black dot on the rinse aid level
indicator changes, as illustrated below.
Full
3/4 full
1/2 full
1/4 full - Should refi ll to eliminate
spotting
Empty
D (Rinse-Aid
indicator)
WATERHARDNESS
Sele
ct
or P
osition
Salt c
onsumption (
gram/c
ycle)
Aut
onomy
(c
ycle s/2 k
gs)
°dH °fH °Clark MmoI/I
0~10 0~17 0~12.5 0~1.7 / 0 /
10~25 17~44 12.5~31.3 1.7~4.4 - 20 60
25~50 44~89 31.3~62.5 4.4~8.9 Mid 40 40
>50 >89 >62.5 >8.9 + 60 25
Contact your local water board for
information on the hardness of your
water supply.