4
Section
1
– Safety Precautions
Install and use in accordance with the manufacturers installation and operation
instructions contained in this manual only.
1.
If this stove is not properly installed, a house fire can occur. For your protection, follow the installation
instructions provided. We recommend contacting local building or fire officials regarding restrictions and
installation inspection requirements in your area.
We also recommend that your Kuma stove be installed
by a properly trained and licensed installer, preferably an NFI (National Fireplace Institute) expert.
2.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE.
3.
Do not burn garbage or flammable fluids such as gasoline, naptha or engine oil
. Do not use charcoal
lighter fluid or similar liquids to start or “freshen up” a fire in this heater. Keep all such fluids well away
from the heater while in use. Storing these fluids near a stove could cause a fire.
4.
DO NOT CONNECT TO ANY AIR DISTRIBUTION OR DUCT SYSTEM.
5.
DO NOT OVERFIRE.
If any part of the stove or chimney glows, the stove is in an overfire condition. If
this happens, shut the air control off immediately. Over firing can cause damage.
6.
WARNING: DO NOT INSTALL IN A SLEEPING ROOM
7.
CAUTION:
THE STRUCTURAL INTEGRITY OF THE FLOOR, WALLS, ROOF/CEILING, AND
VAPOR BARRIERS MUST BE MAINTAINED.
8.
DO NOT USE SINGLE WALL PIPE OR CONNECTOR PIPE FOR ANY CHIMNEY
APPLICATION, EXTERIOR OR THROUGH THE WALL OR CEILING.
Single wall pipe may only
be used as a connection between the stove and an approved masonry or stainless steel chimney.
Single wall
pipe may not be used as a connector in mobile homes.
9.
When installing into an existing masonry or metal chimney, examine the chimney system carefully. If you
have any questions, seek professional advice. We recommend having existing chimneys cleaned and
inspected by a qualified professional prior to the installation of your new stove.
10.
NOTE ALL MINIMUM CLEARANCE REQUIREMENTS TO COMBUSTIBLES.
Installation must
comply with minimum clearances as listed in this manual. (see section 6)
Clearances may only be
reduced by means approved by the regulatory authority.
11.
Do not operate this stove with the door in an open position, except for cracking open during start-up.
Continued operation with the door open can cause overheating of the unit, and expose embers to nearby
combustibles.
12.
Do not operate with broken glass. Do not abuse glass such as striking or slamming the door.
13.
This stove must be connected to a minimum 6” diameter listed chimney that complies with U.L. type 103HT
factory built chimney or a code approved masonry chimney. If the masonry chimney does not meet code, a
U.L. 1777 approved liner must be installed.
14.
When connecting single wall or double wall connector pipe to the stove and chimney, use 3 screws per pipe
joint including 3 screws securing the pipe to the stove. Depending on the type of double wall pipe you are
using, it may also be necessary to fasten it at the chimney. Simpson Duravent’s DVL double wall uses a
snap lock connector and does not need screws.
15.
Use only approved components for Chimney and Connector. Field fabricated or “makeshift” components
are not allowed and can cause a fire.
16.
DO NOT USE THIS STOVE WITHOUT INSTALLING THE BAFFLE BOARDS AND CERAMIC
INSULATION PACKAGED WITH YOUR STOVE.
17.
When connecting this stove to a masonry chimney, make sure you observe all applicable clearances
including walls, ceilings and other combustible material. A masonry chimney must be minimum 6” diameter
and constructed with a liner according to NFPA code 211. If you have any questions about the condition or
the code compliance of your masonry chimney, please speak with a qualified professional.
18.
HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.
CONTACT MAY CAUSE SKIN BURNS.
Содержание K-ASP
Страница 23: ...23 Dimensional Drawings for the Aspen 11 28 25 6 10 9 5 x12 18 5 5 29 25 20 75 23 ...
Страница 31: ...31 63 ...
