KUHN GMD16 Скачать руководство пользователя страница 22

Страница: 22 / 100

GMD16-GMD20

4. - Safety

KN225BGB_A

Disc mower

4.2.10 PTO shaft

- Use only PTO shafts supplied with the machine or

recommended by the machine manufacturer.

- The protective shield of the tractor PTO stub, the

PTO shaft guards and the protective shield of the
machine input shaft must always be in place and in
good condition.

- Make sure that the PTO shaft guards are secured

with the safety chains provided. Check that the
PTO shaft guard can turn freely a full rotation
independent of the shaft.

- Any worn or damaged guards must be replaced

immediately. A worn guard or an unprotected PTO
shaft can cause a serious or even a lethal accident.

- Do not wear loose clothing that could be caught in

the rotating PTO shaft.

- Before attaching or removing a PTO shaft, or

before doing any work on the machine, disengage
the PTO drive, turn off the engine, remove ignition
key and wait for all moving parts to come to a
complete stop.

- If the primary PTO shaft is equipped with a torque

limiter or a free wheel, these must be fitted on the
machine side.

- Ensure that the PTO shaft is always correctly fitted

and locked into place.

- Before connecting the PTO shaft, ensure that the

PTO speed (rotational frequency) and direction of
rotation are in line with the machine manufacturer's
recommendations.

- Before engaging the PTO drive, make sure that

there are no people or animals near the machine.
Never engage the PTO drive when the tractor
engine is stopped.

Содержание GMD16





































































































Результаты поиска

Содержание GMD16

Отзывы:

Похожие инструкции для GMD16

Бренды по названию

Популярные бренды

KUHN GMD16, Руководство оператора

Результаты поиска

Содержание GMD16

Отзывы:

Похожие инструкции для GMD16

Бренды по названию

Популярные бренды