KUHN GMD16 Скачать руководство пользователя страница 87

Страница: 87 / 100

12. - Appendix

GMD16-GMD20

KN225BGB_A

Disc mower

12. Appendix

12.1 Calculating the load on an axle

When coupling a tool to the front and/or rear 3-point lift linkage, the maximum authorized
payload must not be exceeded.

The load on the tractor front axle must always represent 20 % of the tractor unladen weight.

Prior to use, check that these conditions are satisfied by making this calculation or by weighing
the tractor-machine unit.



Define the total weight, axle loads, tyre
capacity and minimum additional mass:

The following values are required for the
calculation:

Description

Units

Description

Obtained

Tractor unladen weight

Unladen load on tractor front axle

Empty load on tractor rear axle

Axle loads (T machine)

Load on front axle (T machine)

Load on rear axle (T machine)

Total weight of front tool or front ballast

Total weight of rear tool or rear ballast

Distance between the tools' centre of gravity or the front ballast and the
front axle centre

Distance between the tractor axles

Distance between the rear axle center and the center of the lower link ball
joints

Distance between the centre of the lower link ball joints and the centre of
gravity of the rear tool or rear ballast

Refer to the tractor operators' manual

Refer to the machine price-list or operators'
manual

Dimensions

Measure on scale

Содержание GMD16





































































































Результаты поиска

Содержание GMD16

Отзывы:

Похожие инструкции для GMD16

Бренды по названию

Популярные бренды

KUHN GMD16, Руководство оператора

Результаты поиска

Содержание GMD16

Отзывы:

Похожие инструкции для GMD16

Бренды по названию

Популярные бренды