KUHN GMD16 Скачать руководство пользователя страница 80

Страница: 80 / 100

GMD16-GMD20

10. - Maintenance and storage

KN225BGB_A

Disc mower

Knives can be turned over on the same disc to use
the other cutting edge or replaced. On each knife,
an arrow indicates the disc's direction of rotation.

- Make sure that the securing nut and bolt are in

good condition and if necessary, replace them.

- Tighten the securing nut of the knives to 12 daN.m

(89 lbf ft).

Dull knives require more horse power and have a
negative effect on the cut quality.

Knife attachment per bolt and nut:

• Knife for disk rotating to the left (Standard):

Part no. K6801410

• Knife for disk rotating to the right (Standard):

Part no. K6801420

• Knife for disk rotating to the left ("HD" discs):

Part no. 56451200

• Knife for disk rotating to the right ("HD"

discs): Part no. 56451300

Knife attachment per bolt and nut:

• Bolt: Part no. 56115800
• Nut: Part no. 80201262

Содержание GMD16





































































































Результаты поиска

Содержание GMD16

Отзывы:

Похожие инструкции для GMD16

Бренды по названию

Популярные бренды

KUHN GMD16, Руководство оператора

Результаты поиска

Содержание GMD16

Отзывы:

Похожие инструкции для GMD16

Бренды по названию

Популярные бренды