KUHN GF7702T Скачать руководство пользователя страница 14

Страница: 14 / 72

Gyrotedder

GF7702T

Safety

Stage 4:

To measure:

- Load on rear axle (t2):

• T machine (transport position).
• Ballast weights.

Checking:

- Check in the tractor's operator's manual that the value

measured is below the maximum allowed tractor rear
axle load.

- Check that tyre and rim specifiations are in conformity

with the requirements of the tractor manufacturer.

Example:

• Load on rear axle (t2) = 8500 kg (18740 lb)
• Check in the tractor's operator's manual that the

value measured is below the maximum allowed
tractor rear axle load.

• Check that tyre and rim specifiations are in

conformity with the requirements of the tractor
manufacturer.

Maximum speed

Always keep to the legal speed limit for driving a tractor-

machine assembly on public roads.

Содержание GF7702T









































































Результаты поиска

Содержание GF7702T

Отзывы:

Похожие инструкции для GF7702T

Бренды по названию

Популярные бренды

KUHN GF7702T, Руководство оператора

Результаты поиска

Содержание GF7702T

Отзывы:

Похожие инструкции для GF7702T

Бренды по названию

Популярные бренды