KUHN GF10802T Скачать руководство пользователя страница 61

Страница: 61 / 72

Maintenance and storage

Gyrotedder

GF10802T

Tyre pressure

- Transport wheels (1): 2.2 bar (32 psi).
- Central parts (2): 2.0 bar (29 psi).
- Outer wings (3): 1.5 bar (22 psi).

4. Storage

At the end of each season:

- Clean the machine thoroughly.
- Lubricate the whole machine.
- Check tyre pressure:

• Transport wheels: 2.2 bar (32 psi).
• Central parts: 2.0 bar (29 psi).
• Outer wings: 1.5 bar (22 psi).

- Touch up any areas of damaged paintwork.
- Check and replace worn or damaged tines.
- Put the machine under cover in a dry place.

At the start of each season:

- Re-read the operators' manual.
- Check tyre pressure:

• Transport wheels: 2.2 bar (32 psi).
• Central parts: 2.0 bar (29 psi).
• Outer wings: 1.5 bar (22 psi).

- Check that all nuts and bolts are sufficiently tightened.
- Make sure that all protection devices are in place and

in good condition.

Содержание GF10802T









































































Результаты поиска

Содержание GF10802T

Отзывы:

Похожие инструкции для GF10802T

Бренды по названию

Популярные бренды

KUHN GF10802T, Руководство оператора

Результаты поиска

Содержание GF10802T

Отзывы:

Похожие инструкции для GF10802T

Бренды по названию

Популярные бренды