KUHN GA4121GM Скачать руководство пользователя страница 43

Страница: 43 / 88

8. - Instructions for work

GA4121GM

KN129DGB D

Gyrorake

8.2

Adjustments in working position

8.2.1 Wheel height adjustment

- Raise machine using tractor lift linkage so that

wheels are no longer in contact with the ground.

- Place one hand underneath wheel to free pin (2)

from vertical adjustment plate (3) and operate
lever (1).

Before manoeuvring the machine:

- Check that nobody is within the machine

pivoting area.

- If there is someone, make sure the person

moves away.

When optional equipment is used, follow
specific procedures mentioned in the related
section:

•  Optional equipment / Front support wheel.
•  Optional equipment / Bogie axles.
•  Optional equipment / Hydraulic windrow

curtain.

Before leaving the tractor or before
adjusting, maintaining or repairing the
machine, disengage the PTO drive, turn off
the engine, remove ignition key and wait until
all moving parts have come to a complete
stop and apply park brake.

Содержание GA4121GM

























































































Результаты поиска

Содержание GA4121GM

Отзывы:

Похожие инструкции для GA4121GM

Бренды по названию

Популярные бренды

KUHN GA4121GM, Руководство оператора

Результаты поиска

Содержание GA4121GM

Отзывы:

Похожие инструкции для GA4121GM

Бренды по названию

Популярные бренды