KUHN FC2860TLD Скачать руководство пользователя страница 57

Страница: 57 / 120

8. - Instructions for work

FC2860TLD-3160TLD-3560TLD

KN281CGB_L

Mower conditioner

- To change the speed, use lever (1):

• Select the hare position to obtain a rotor speed of

1000 min-1.

• Select the tortoise position to obtain a rotor speed

of 780 min-1.

- Slightly rotate the discs by hand to facilitate the

gear engagement.

8.2.4 Conditioning intensity

- Before adjusting, maintaining or repairing

the machine, turn off ignition key and wait
until all moving parts have come to a
complete stop.

Several factors govern the conditioning intensity
adjustment:



Conditioning rotor speed

- See section "Finger conditioning rotor speed".



Adjustment lever (1)

The lever sets the conditioning hood in relation to
the rotor in 5 positions.

- To increase the conditioning intensity, reduce the

distance between the conditioning hood and the
conditioning rotor.

- To reduce the conditioning intensity (for mowing

leguminous for example), increase the distance
between the conditioning hood and the
conditioning rotor.

Содержание FC2860TLD

























































































































Результаты поиска

Содержание FC2860TLD

Отзывы:

Похожие инструкции для FC2860TLD

Бренды по названию

Популярные бренды

KUHN FC2860TLD, Руководство оператора

Результаты поиска

Содержание FC2860TLD

Отзывы:

Похожие инструкции для FC2860TLD

Бренды по названию

Популярные бренды