KUHN FC2860TLD Скачать руководство пользователя страница 115

Страница: 115 / 120

12. - Troubleshooting guide

FC2860TLD-3160TLD-3560TLD

115

KN281CGB_L

Mower conditioner

Badly shaped windrows.

Too low PTO speed
(rotational frequency).

- Check PTO speed. Refer to the

decal fitted on the machine.

Rotor speed too high.

- Select the tortoise position to

obtain a rotor speed of 780 min-1.

Incorrectly adjusted swath
shields.

- Adjust both swath shields.

Machine requires too
much pull power.

Too much cutterbar down
pressure.

- Adjust the mowing unit ground

pressure.

Rotor finger rattle.

Insufficient rotor speed.

- Select the hare position to

obtain a rotor speed of
1000 min-1.

Conditioning hood is too
closed.

- Position rotor conditioning hood

further away.

Excessive ground speed.

- Reduce groundspeed.

Impossible to decrease or
increase the mowing unit
ground pressure
sufficiently.

Soil build-up on the
machine.

and

Maximum ground
pressure reduction.

- Adjust torsion bars of the

ground pressure system. (See
maintenance and storage
chapter)

Insufficient ground
pressure.

and

Minimum ground pressure
reduction.

The rotor is no longer
driven.

The safety system shear
bolt has sheared.

- Replace screw. (See

maintenance and storage
chapter)

Wide spreading of poor
quality.

Incorrect cover position.

- Tip cover over the wide

spreading device.

Содержание FC2860TLD

























































































































Результаты поиска

Содержание FC2860TLD

Отзывы:

Похожие инструкции для FC2860TLD

Бренды по названию

Популярные бренды

KUHN FC2860TLD, Руководство оператора

Результаты поиска

Содержание FC2860TLD

Отзывы:

Похожие инструкции для FC2860TLD

Бренды по названию

Популярные бренды