KUHN ATHENOR 6070 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 98

background image

Silo unloader - Straw spreader - Mixer - Distributor

60

ATHENOR 6070

Instructions for work

9. Distribution

Select the blower speed for feeding: 270 min

-1

.

The distribution chute on the right of the machine is used

for 2 purposes.

For optimal quality of work and product positioning in the

designed place, the distribution chute cap can be set to
three positions.

For easy manual adjustment of the position, open the

chute halfway.

Pull the handle down.

Put the spindle into the desired notch (the most external

one sets the cap to the greatest angle of tilt).

Operating tips:

To stop the distribution (posts, obstacles) disengage the

beater bar. (The conveyor stops at the same time).

To avoid clogging the machine in difficult conditions,

watch the engine speed carefully. Slow down conveyor
speed or even reverse the direction if the engine speed
drops or the belt starts to slip. If it becomes overloaded,
allow it to empty before making the conveyor move
forward again.

Always start the tractor PTO before engaging the
beater bar. Stop the beater bar before stopping
the PTO. If you do not do this in the right order,
you are very likely to block up the blower.

«
...
60
61
62
63
64
...
»

Содержание ATHENOR 6070



































































































Отзывы:

Нет отзывов

Похожие инструкции для ATHENOR 6070

Бренд: Landoll Страницы: 52

Бренд: JBSYSTEMS Light Страницы: 14

Бренд: YardShape Страницы: 50

Бренд: EarthQuake Страницы: 28

Бренд: TAIKO Audio Страницы: 24

Бренд: Ibiza Страницы: 21

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: Kamikaze Страницы: 112

Бренд: KAM Страницы: 2

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Saturn 2000 GC/MS

Бренд: Varian Страницы: 9

Бренд: XFit Страницы: 16

BlackBox Series

Бренд: Nakamichi Страницы: 23

Бренд: Harken Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды