Kubota SQ-1120 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 63

Kubota SQ-1120 Скачать руководство пользователя страница 8

3

SAFE OPERATION

KEEP THE AREA AROUND THE ENGINE CLEAN

A

Be sure to stop the engine before cleaning.

A

Keep the engine clean and free of accumulated dirt,
grease and trash to avoid a fire. Store flammable fluids
away from sparks and fire.

A

DO NOT stop the engine without idling. Sudden stops
can cause temperatures around the engine to rise
suddenly. Keep the engine idling for about 5 minutes
before stopping.

SAFE HANDLING OF FUEL AND LUBRICANTS

A

Always stop the engine before refueling and/or
lubricating.

A

DO NOT smoke or allow flames or sparks in the working
area. Fuel is extremely flammable and explosive under
certain conditions.

A

Refuel only when the engine has cooled off. Refuel in a
well ventilated and open place. When fuel and lubricants
are spilled, clean them up before starting the engine.

A

DO NOT mix gasoline or alcohol with diesel fuel. The
mixture can cause a fire and damage engine
components.

A

Operate the generator on a firm and level surface only.
DO NOT tilt or move the generator while it is running
since this can cause fuel spillage.

1G296-8914.book 3 ページ２０１２年３月１９日　月曜日　午前１０時４０分

«
...
6
7
8
9
10
...
»

Содержание SQ-1120
































































Отзывы:

Нет отзывов