Kubota SQ-1120 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 63

Kubota SQ-1120 Скачать руководство пользователя страница 50

35

PERIODIC SERVICE

FAN BELT

B

Adjusting Fan Belt Tension

To avoid personal injury:

A

Be sure to stop the engine and
remove the key before checking the
belt tension.

A

Be sure to reinstall the detached
safety shield after maintenance or
checking.

[Engine model : D1703-EBG, V2203-EBG]

[Engine model : V3300-EBG]

1. Stop the engine and remove the key.
2. Apply moderate thumb pressure to belt between

pulleys.

3. If tension is incorrect, loosen the alternator mounting

bolts and, using a lever placed between the alternator
and the engine block, pull the alternator out until the
deflection of the belt falls within acceptable limits.

4. Replace fan belt if it is damaged.

A

If belt is loosen or damaged and the fan is damaged,
it could result in overheating or insufficient charging.
Adjust correctly or replace the belt.

FULLY BUNDED

A

Before installing the unit all environmental factors
must be considered.
Generator installation must comply with local building
codes, fire regulations and environmental
requirements.
Use these instructions as a general guide only, the
complete installation must comply with all local, state,
and federal building codes, fire ordinances, and any
other applicable regulations.

1. Open the access door and check for anything unusual

every workday.

2. Look at the point (1) to make sure anything

accumulated will not spill out.

3. If an accumulation may come out, loosen the plug (3)

to drain the unit.

4. Finally, retighten up the plug.

L

Proper fan belt
tension

A deflection of between 7 to 9 mm
when the belt is pressed in the
middle or the span.

Proper fan belt
tension

A deflection of between 10 to 12 mm
when the belt is pressed in the
middle of the span.

(1) Fan belt
(2) Bolt and nut

[D1703-EBG, V2203-EBG]

(A) 7 to 9 mm (under load of 98 N)

[V3300-EBG]

(A) 10 to 12 mm (under load of 64 N)

(1) Check point
(2) Fully bunded (Base bunded to 110% capacity)
(3) Containment drain point (Plug size: 3/4)

Engine model

Fully bunded capacity

D1703-EBG, V2203-EBG

84

V3300-EBG

104

1G296-8914.book 35 ページ２０１２年３月１９日　月曜日　午前１０時４０分

«
...
48
49
50
51
52
...
»

Содержание SQ-1120
































































Отзывы:

Нет отзывов