manualshive.com logo in svg

Kubota Impac 500, Руководство пользователя

Поделиться
Скачать
Kubota Impac 500 Скачать руководство пользователя страница 4

SAFETY 

CAUTION

 

READ THIS ENTIRE OPERATOR’S MANUAL BEFORE BEGINNING WORK 

ALWAYS WEAR SAFETY GLASSES AND USE CARE WHEN  WORKING WITH POWER TOOLS 

Safety is a primary concern in the design and manufacturing of IMPAC™ products.  Unfortunately, all efforts to 
provide safe equipment can be totally negated by a single careless act by an Installer or Operator. 

Accident Prevention and Safety are dependent upon the awareness and proper training of the personnel who 

operate and maintain this equipment.  The best safety device is a careful and informed Owner/Operator. 

Taking precedence over any specific rule, however, is the most important rule of all:  SAFETY FIRST 

IMPAC™  Model P500™ lift system has a rated lift capacity of 227 kg (500 lbs) 

Maximum Load capacity at full extension – 227 kg (500 lbs) 

Maximum Winch load capacity at full extension – 227 kg (500 lbs) 

Maximum Vehicle operating angle – 5 degrees 

OVERLOADING YOUR VEHICLE CAN CAUSE POTENTIAL SAFETY HAZARDS!

 

Read and obey all Safety Symbols, Warnings, Cautionary Notes and Operating 

Instructions on the IMPAC 500™  and in this Manual. 

Ensure that all placards are in place and legible. 
Failure to comply with safety precautions in this Manual and on the IMPAC 500™ 

is a safety violation that may result in serious injury, death or property damage. 

SAFETY LABELS 

Understanding Machine Safety Labels 

The unit’s Safety Labels, as shown in this section, are placed in important areas on your IMPAC 500™  unit  to 
draw attention to potential safety hazards. 

The Safety Labels on your unit are pictorial, ensuring they are most easily and universally understood. 

Where necessary, the Operator’s Manual explains any potential safety hazards in special safety messages 

identified with the words CAUTION or BE CAREFUL, and incorporate the Safety-Alert symbols shown below. 

Page 2 

Содержание Impac 500





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды