KTM F7103U6 Скачать руководство пользователя

Страница: 36 / 47

3 WORK

The boundary between light and dark must be exactly on the
lower mark for a motorcycle with rider.

» If the boundary between light and dark does not meet

specifications:

–

Adjust the headlight range. (

p. 34)

3.24

Adjusting the headlight range

Preparatory work

–

Check the headlight setting. (

p. 33)

V00369-10

Main work

–

Loosen screw

–

Adjust the headlight range by pivoting the headlight.
Guideline

The boundary between light and dark must be exactly on the
lower mark for a motorcycle with rider (instructions on how
to apply the mark: Checking the headlight setting).

Info

If you have a payload, you may have to correct the
headlight range.

–

Tighten screw

3.25

Installing the engine guard

H01638-10

–

Attach the engine guard on the frame at the rear and swing up
at the front.

–

Mount and tighten screws

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

3.26

Opening 2-stroke oil tank cap

E00861-10

–

Fold loop

upward.

–

Turn the 2-stroke oil tank cap counterclockwise and pull it up.

Содержание F7103U6
















































Результаты поиска

Содержание F7103U6

Отзывы:

Похожие инструкции для F7103U6

Бренды по названию

Популярные бренды

KTM F7103U6, Инструкции по установке

Результаты поиска

Содержание F7103U6

Отзывы:

Похожие инструкции для F7103U6

Бренды по названию

Популярные бренды