Eng
lish – Pa
ge 2
0
De
uts
ch – S
eit
e 2
0
English –
4
Displays and configurations of the
on-board computer
Battery charge indicator
The battery charge indicator
(g)
displays the eBike battery's
state of charge. The state of charge of the eBike battery can
also be checked on the LEDs of the battery itself.
In the indicator
(g)
, each bar in the battery symbol repres-
ents approximately 20 % capacity:
The eBike battery is fully charged.
The eBike battery should be recharged.
The LEDs of the battery charge indicator on the
battery go out. The capacity for assisting the drive
has been used up, and assistance is gently
switched off. The remaining capacity is made
available for the lighting. The indicator flashes.
The capacity of the eBike battery is enough for
about two hours of lighting.
Speed and distance indicators
The speedometer
(a)
always displays the current speed.
Indicator
(i)
always displays the last setting as standard. Re-
peated medium-length presses of the button
–
will display
the trip distance
TRIP
, the total distance
TOTAL
and the
range of the battery
RANGE
one after the other. (Briefly
pressing the button
–
will decrease the assistance level.)
To
reset
the trip distance
TRIP
, select the trip distance
TRIP
and simultaneously press and hold the buttons
+
and
–
.
The display will initially show
RESET
. If you continue to press
both buttons, the trip distance
TRIP
will be set to
0
.
To
reset
the range of the battery
RANGE
, select the battery
range
RANGE
and simultaneously press and hold the but-
tons
+
and
–
. The display will initially show
RESET
. If you
continue to press both buttons, the trip distance
TRIP
will be
set to
0
.
You can switch the displayed values from kilometres to miles
by holding down the button
–
and briefly pressing the
on/off button
(1)
.
The versions of the subsystems and their model part num-
bers can be displayed for the purposes of servicing,
provided the subsystems divulge this information (depend-
ent on the subsystem). With the system
switched off
, simul-
taneously press the buttons
–
and
+
and then press the on/
off button
(1)
.
The USB port is reserved for connecting diagnostic systems.
The USB port does not have any other function.
u
The USB connection must always be completely
sealed with the protective cap
(8).
Action
Buttons Duration
Switch on on-board computer
Switch off on-board computer
Increase assistance
+
Decrease assistance
–
Display
TRIP
,
TOTAL
,
RANGE
,
assistance modes
–
Switch on bike lights
+
Switch off bike lights
+
Reset trip distance
–
+
Activate push assistance
Implement push assistance
WALK
+
1.
2. Any
Switch from kilometres to miles
–
1. Keep
pressed
2.
Display the versions
A)B)
–
+
1. Keep
pressed
2.
Adjust display brightness
C)
–
+
–
or
+
1. Keep
pressed
2.
A) The eBike system must be switched off.
B) The information is shown as scrolling text.
C) The display must be switched off.
1 207 020 XBP | (11.03.2020)
Bosch eBike Systems
Содержание BUI215
