KTM 990 Adventure AUS Скачать руководство пользователя страница 89

Страница: 89 / 218

SERVICE WORK ON THE CHASSIS

100617-11

–

Raise the fuel tank slightly and attach it to the upper holder.

–

Mount and tighten screws



Guideline

Screw, fuel tank

15 Nm
(11.1 lbf ft)

–

Install the storage compartment.

(

p. 84)

–

Install the front side cover. (

p. 80)

–

Turn the knurled screws on both fuel taps counterclockwise as far as possible.

–

Check the fuel system for leaks.

10.16

Checking for chain dirt

400678-01

–

Check the chain for coarse dirt accumulation.
» If the chain is very dirty:

–

Clean the chain. (

p. 87)

10.17

Cleaning the chain

Warning

Danger of accidents

Oil or grease on the tires reduces their grip.

–

Remove oil and grease with a suitable cleaning material.

Содержание 990 Adventure AUS



























































































































































































































Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

KTM 990 Adventure AUS, Руководство пользователя, Страница: 89 / 218

Результаты поиска

Содержание 990 Adventure AUS

Отзывы: