manualshive.com logo in svg

KTM 990 Adventure AUS, Руководство пользователя, Страница: 82 / 218

Поделиться
Скачать
KTM 990 Adventure AUS Скачать руководство пользователя страница 82

SERVICE WORK ON THE CHASSIS

80

100589-10

–

Remove screws

.

–

Carefully swing out the side cover

at the top and disconnect the plug-in connectors

of the turn signal cables.

–

Pull off the overflow hose of the fuel tank and take off the trim.

10.7

Installing the front side cover

Info

The operations are the same on the left and right sides.

100589-11

–

Position side cover

at the fuel tank on the bottom and hold it at an angle.

–

Attach the overflow hose of the fuel tank to the connector.

–

Connect the plug-in connectors of the turn signal cables and swing the side cover up
toward the vehicle.

–

Mount and tighten screws

with the washers.

Guideline

Remaining chassis nuts

M6

15 Nm
(11.1 lbf ft)

–

Check the function of turn signal.

Содержание 990 Adventure AUS



























































































































































































































Отзывы:

Нет отзывов