KTM 250 EXC-F 2019 Скачать руководство пользователя

Страница: 36 / 48

3 WORK

3.18

Installing the fuel tank

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

Main work

–

Check throttle cable routing. (

p. 35)

–

Position the fuel tank and fit the two spoilers to the sides in
front of the radiator bracket.

–

Make sure that no cables or throttle cables are trapped or dam-
aged.

K00556-10

–

Attach the fuel tank breather hose.

–

Mount and tighten screw

with the rubber bushing.

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

K00558-11

–

Position the horn with the horn bracket.

–

Mount and tighten screws

with the collar bushings.

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

Содержание 250 EXC-F 2019

















































Результаты поиска

Содержание 250 EXC-F 2019

Отзывы:

Похожие инструкции для 250 EXC-F 2019

Бренды по названию

Популярные бренды

KTM 250 EXC-F 2019, Инструкции по установке

Результаты поиска

Содержание 250 EXC-F 2019

Отзывы:

Похожие инструкции для 250 EXC-F 2019

Бренды по названию

Популярные бренды