KTM 1190 RC8 R Track страница 68 Скачать руководство пользователя

Страница: 68 / 127

BRAKES

11.1

Checking the front brake discs

Warning

Danger of accidents

Reduced braking efficiency due to worn brake disc(s).

–

Change the worn brake disc(s) without delay. (Your authorized KTM RC8 workshop will be pleased to help.)

100135-10

–

Check the thickness of the brake disc in several places to see if it is within the
specified wear tolerance



Info

Wear reduces the thickness of the brake discs in area



of the brake discs.

Brake discs - wear limit

Front

4.5 mm (0.177 in)

» If the brake disc thickness is less than the specified value:

–

Change the brake discs.

–

Check the brake discs for damage, cracking and deformation.
» If the brake discs exhibit damage, cracking or deformation:

–

Change the brake discs.

11.2

Checking the rear brake disc

Warning

Danger of accidents

Reduced braking efficiency due to worn brake disc(s).

–

Change the worn brake disc(s) without delay. (Your authorized KTM RC8 workshop will be pleased to help.)

400480-10

–

Check the thickness of the brake disc in several places to see if it conforms to mea-
surement



Info

Wear reduces the thickness of the brake disc in area



of the brake disc.

Brake disc - wear limit

Rear

4.5 mm (0.177 in)

» If the brake disc thickness is less than the specified value:

–

Change the brake disc.

–

Check the brake disc for damage, cracking and deformation.
» If damage, cracks or deformation are visible on the brake disc:

–

Change the brake disc.

11.3

Adjusting the basic position of the hand brake lever

601447-10

–

Pull the brake lever forwards.

–

Adjust the basic setting of the hand brake lever to your hand size by turning adjust-
ing wheel



Info

Do not make any adjustments while riding!

Содержание 1190 RC8 R Track
































































































































Результаты поиска

Содержание 1190 RC8 R Track

Отзывы:

Похожие инструкции для 1190 RC8 R Track

Бренды по названию

Популярные бренды

KTM 1190 RC8 R Track, Руководство пользователя

Результаты поиска

Содержание 1190 RC8 R Track

Отзывы:

Похожие инструкции для 1190 RC8 R Track

Бренды по названию

Популярные бренды