KTI Networks KGS-1260/G Скачать руководство пользователя страница 25

Страница: 25 / 34

-25-

3.4 LED Indication

LED

Function

Color

State

Interpretation

PWR

Power
status

Green

The power is supplied to the switch.

OFF

The power is not supplied to the switch.

Mgt

Management status Green

BLINK

The switch is in initialization and diagnostics.

Yellow

BLINK

Initialization completed with diagnostic error or system error found during normal operation

Green

Initialization completed with no error

Port1 ~ Port 8

SPEED_LED

Port speed status

Green

Speed is 1000Mbps.

Yellow

Speed is 10Mbps or 100Mbps.

LINK_LED

Port link status

Green

Port link is established. (No traffic)

BLINK

Port link is up and there is traffic.

OFF

Port link is down.

Port 9 ~ Port 12

SPEED_LED

Port speed/link
status

Green

A 1000Mbps link is established.

Yellow

A 100Mbps link is established.

BLINK

Activity status

OFF

Port link is down.

Содержание KGS-1260/G



































Результаты поиска

Содержание KGS-1260/G

Отзывы:

Похожие инструкции для KGS-1260/G

Бренды по названию

Популярные бренды

KTI Networks KGS-1260/G, Руководство по установке

Результаты поиска

Содержание KGS-1260/G

Отзывы:

Похожие инструкции для KGS-1260/G

Бренды по названию

Популярные бренды