KSB Etanorm V Скачать руководство пользователя страница 36

Страница: 36 / 62

7 Servicing/Maintenance

36 of 62

Etanorm V

1228.87/01-EN

Table 16:

Clearances between impeller and casing

Casing wear rings

502.01/.02

Bearing cartridge 381.01/

bearing sleeve 529.16

Material variant

GG, CC

SU 25/35

SU 55

As-new

0.3 mm

0.5 mm

0.12 mm

0.14 mm

Maximum permissible
enlargement

0.9 mm

1.5 mm

0.25 mm

0.3 mm

7.3 Drainage/cleaning

WARNING

Fluids handled, consumables and supplies which are hot and/or pose a health
hazard

Hazard to persons and the environment!

▷

Collect and properly dispose of flushing fluid and any fluid residues.

▷

Wear safety clothing and a protective mask if required.

▷

Observe all legal regulations on the disposal of fluids posing a health hazard.

1. Always flush the pump if it has been used for handling noxious, explosive, hot

or other hazardous fluids.
Always flush and clean the pump before transporting it to the workshop.
Provide a cleaning record for the pump.

7.4 Dismantling the pump set

7.4.1 General information/Safety regulations

DANGER

Insufficient preparation of work on the pump (set)

Risk of injury!

▷

Properly shut down the pump set.

▷

Close the shut-off elements in the suction line and discharge line.

▷

Drain the pump and release the pump pressure. (

Section 7.3, Page 36)

▷

Shut off any auxiliary feed lines.

▷

Allow the pump set to cool down to ambient temperature.

WARNING

Unqualified personnel performing work on the pump (set)

Risk of injury!

▷

Always have repair work and maintenance work performed by specially trained,
qualified personnel.

WARNING

Hot surface

Risk of injury!

▷

Allow the pump set to cool down to ambient temperature.

Shaft unit see data sheet.

Содержание Etanorm V































































Результаты поиска

Содержание Etanorm V

Отзывы:

Похожие инструкции для Etanorm V

Бренды по названию

Популярные бренды

KSB Etanorm V, Руководство по эксплуатации

Результаты поиска

Содержание Etanorm V

Отзывы:

Похожие инструкции для Etanorm V

Бренды по названию

Популярные бренды