KRUSMAN 7023 Скачать руководство пользователя страница 9

 

Use 

Body Showers with pull rod 

Pull the lever handle all the way down to the valve lever limit stop. 
 
After the shower has started: 
Remove all contaminated clothing which is not stuck to your skin, and rinse all  affected areas with 
cool,  clean  water.  EN  and  ANSI  standards  recommend  flushing  for  15  minutes  continuously,  seek 
your local safety regulations for further advice and recommendations.  
 
In order to stop the shower, push the pull rod lever up, until the valve is closed. 

Seek medical attention! 

Models with Optional Eye Shower 

Rotate/push  the  actuating  lever  a  quarter  turn  in  order  to  start  the  eye/face  wash  shower.  After 
doing so, the dust cover move from the eye/face shower as a result of the first surge of water starts. 
 
The eye shower should not make direct contact with the contaminated eye or any surrounding areas. 
Ideal rinsing is assured at a distance of approximately  15 cm (seek your local safety regulations for 
further advice and recommendations). 
 
In order to stop the shower, pull the lever up until the valve is closed. 

Seek medical attention!

 

 

Models with Optional Heater 

If an electrical heating is installed, it has been connected by a licensed electrician and is functioning 
correctly when the unit has left our warehouse. In this connection the safety instructions have been 
followed.  A  maximum  water  temperature  of  approximately  +25°  C  is  preset  at  the  factory.  The 
temperature can be conveniently checked with the thermometer (optional). 
 
This  temperature  may  be  fallen  short  of,  depending  upon  local  conditions  at  the  installation  site 
(wind-chill  factor  etc.).  The  heaters  are  equipped  with  a  regulator,  by  means  of  which  the 
temperature can be adjusted if required (see details in separately enclosed instructions for use). The 
operation  manual  from  the  supplier  is  included  when  the  item  is  shipped  to  the  purchaser.  The 
submersible heating element is designed to work when the trailer is connected to its power source 
and  the  water  temperature  has  been  detected  that  it  is  below  approximately  15°C.  It  will  then 
operate  until  the  water  contained  in  the  tank  will  reach  approximately  25°C  and  then  switch  off 
again. 

 

Red  light  as  seen  below  means  the  heating  element  is  working.  Please  be  aware  that  there  is  a 
automatic  cut  off  switch  installed  for  the  heating  element.  This  prevents  the  heating  element 
working when there is an insufficent amount of water contained in the tank, thus avioding the heater 
to over heat. 

 

Содержание 7023













Отзывы: