Kromschroder BCU 465 Скачать руководство пользователя страница 23

Страница: 23 / 31

T-Product · BCU 465 · 2006 April

Factory Options and Field Programmable Options

Flame Proving Period, Param-

eter 23

The ﬂame proving period (delay for

valve 2) is between 0 seconds and

25 seconds.

This time is the delay for high ﬁre

mode. For BCU..O (POC-version),

this means delay for allowing external

air valve control (also see parameter

31); for BCU without POC input this

time is delay for gas valve 2 terminal

#14.

Manual Mode Limit, Parameter

If parameter 34 is set =1, the BCU

will return to standby 5 minutes

after the reset/info button was last

pressed. If parameter 34 is set =0,

the BCU will remain in its current

operational state for an unlimited

time.

Automatic Shutdown and Re-

start after 24 hr Operation, Pa-

rameter 35

If UVS 6 or UVS 8 UV detectors are

used, this function is recommended

to self check the UV detector every

day: parameter 35 = 1: restart, pa-

rameter 35 = 0 continue.

Note: Description of parameters 30,

31, 32 and 36 through 41 see Air

Valve Control of BCU 465

Reading the Parameters

Reading the ﬂame signals, factory

options and ﬁeld programmable op-

tions are explained as follows:

• Press the Reset/Information but-

ton for 2 seconds.

➔

The display changes to param-

eter 01

• Release the button.

➔

The display stops at this param-

eter and indicates the related

value.

• Press the button again for 2 sec-

onds.

➔

The display changes to the next

parameter.

• All parameters can be recalled

consecutively in this way.

• If the button is pressed only

brieﬂy, the display indicates what

parameter is currently being dis-

played.

• The normal program status is

displayed again approx. one

minute after the button was last

pressed or if all parameters are

recalled or if BCU is switched off.

Содержание BCU 465
































Результаты поиска

Содержание BCU 465

Отзывы:

Похожие инструкции для BCU 465

Бренды по названию

Популярные бренды

Kromschroder BCU 465, Техническая информация

Результаты поиска

Содержание BCU 465

Отзывы:

Похожие инструкции для BCU 465

Бренды по названию

Популярные бренды