background image

The Woofer

The E8B’s woofer construction is that of a multi-layered sandwich, consisting of two layers
of Kevlar with a layer of Rohacell in between. Rohacell is a polymethacrylimide (PMI) hard
foam that is used as a core material for sandwich constructions. Rohacell is an extremely
lightweight material that, in addition to providing additional stiffness for the woofer’s 
construction, functions as a damping material to eliminate unwanted resonances. The E8B
copper pole cap and the aluminum shorting ring reduce motor induced distortions to an
amazingly low level.  The woofer’s multi-layered construction also reduces distortion for
greater signal reproduction accuracy.

Rear Panel Controls

A) System Level Adjust

This control adjusts

the sensitivity of 
the input signal.
Rotating the control
clockwise increas-
es sensitivity while
counterclockwise
rotation decreases

s e n s i t i v i t y . T h e

adjustment range is from -30 dB to +6
dB. The default setting is +6 dB, which
should suffice for most applications.
Normally, adjustments would only be
made if you are using your monitors in
a surround environment and you need
to balance levels, or if your monitor
sends are too hot and not adjustable. If
an adjustment becomes necessary, it is
recommended to use measuring equip-
ment such as a tone or filtered noise
generator and an SPL meter.

B) HF Shelf Switch 

This switch provides the ability to adjust the high frequencies using a shelf EQ with the
option to increase or decrease the level of the frequencies above the shelf threshold.
Experimentation is key to the successful use of this system parameter. It is made available
to facilitate modification to the loudspeaker’s sound quality if, for example, you find the
sound to be too bright or lacking an “airy” quality.  This is a 7-position switch with 
adjustments in .5dB steps and includes the following gain settings:  +1.0, +0.5, 0, -0.5, -1.0,
-1.5, -2.0. It is recommended to set this control to 0 and 
listen carefully before adjusting to your preferences.

6

Содержание EXPOSE E8B

















Отзывы: