background image

 

General information 

1.1 

Description 

The INT69 YF Diagnose tripping device is a versatile universal protection device. Various temperature, 
voltage, leakage/resistance measurement and analogue signal inputs are available in a single module 
for monitoring electrical components. Parametrization enables protection function and response 
settings to be adapted flexibly to suit the application. The INT69 YF Diagnose saves operating and 
fault data in a non-volatile memory. This data can be read out and evaluated for diagnostics purposes. 
This tripping device is used primarily for the protection of pumps. 

 

1.2 

Additional documents 

In connection with these operating instructions, the following documents should be observed: 

• 

The data sheet for the Diagnose diagnostics device 

• 

General or application-specific SOPs within the context of the Health and Safety at Work Act 
and the Ordinance on Work Equipment and Tools 

• 

Accident prevention regulations 

• 

Legal regulations 

• 

Local regulations 

 

1.3 

Symbols used 

Meaning of the symbols and safety notices used in this document. 
 

Please note that a safety symbol is never a substitute for a safety notice in text form - 

therefore always read all safety notices! 

This document contains information that must be observed to avoid personal injury and equipment damage. 
Safety information to avoid personal injury is indicated by means of a color code with a warning 
triangle and a signal word defined in accordance with ANSI Z535.6-2006: A1.2. 
The signal words are classified according to ANSI Z535.6-2006: C4.2. 
Depending on the degree of risk, the notices are shown as follows: 
 

This indicates that death or serious injury will occur if the relevant precautions are not 
taken here! 

 

This indicates that death or serious injury may occur if the relevant precautions are not 
taken here 

 

This indicates that minor injury may occur if the relevant precautions are not 
taken here! 

 

This denotes information and tips for use. It does not represent a safety notice. 

 
The text of a safety notice is divided into: 
_________________________________________________________________________________ 

Description of the nature/source of the danger 

 

Description of the consequences of disregarding the safety notice.

 

  Measures for avoidance 

_________________________________________________________________________________ 

 

 

Содержание INT69 YF Diagnose Extended 20A701P081



























Отзывы: