KRESS KU041, Быстрый старт

Страница: 5 / 8

5
EN
OPERATING INSTRUC-
TIONS
NOTE: Before using the tool, read the
instruction book carefully.
Before using this tool:
Before starting the job it is advisable to test the
workpiece for the ideal temperature to use.
The description below gives an indication of the
likely heat settings required but always start with the
low heat setting.
The distance between the nozzle and the workpiece
will vary according to the material being worked on
but this should always be at least 50 mm or more on
any heat setting.
All applications, with the exception of removing
paint from the window frames, can be performed
without using a nozzle; however for best results
nozzles are recommended.
PUTTING INTO OPERATION (SEE FIG A)
1. SWITCHING ON/OFF
SWITCHING ON:
To switch off, slide the on/off switch (5) to the stop at
position 0.
Switching off:
To switch off, slide the on/off switch (5) to the stop at
position 0.
2. SETTING THE AIR FLOW AND TEMPERATURE
(SEE FIG B)
The switch (5) can be set to two blower settings.
Suitable airflow and temperature combinations can
be selected according to the applications.
I =50 - 600°C(120 - 1100°F), 300 L/min (8.1CFM)
II = 50 - 600°C(120 - 1100°F), 500L/min (13.5CFM)
The air setting I is suitable for Bending Plastic and
heating-shrinking plastic.
The air setting II is suitable for stripping paint and
defrosting pipes.
Temperature can be adjusted in increments of 10 °C
(20°F) from 50°C (120°F) to 600°C
(1100°F) by pressing the temperature control button
(12) on the LCD cover (11).
°F or °C can be selected by pressing°F / °C
3. NOZZLES SELECTION
The kit is supplied with 4 different shaped
nozzles, which can be used as follows:
1)CONCENTRATION NOZZLE (16)
This nozzle directs a concentrated heat flow to the
workpiece. It is ideal for use when removing paint
in awkward corners, crevices, mouldings, beading,
architraves or whenever precise paint removal is
required.
2)FLAT NOZZLE (14)
This nozzle directs a long narrow heat pattern to the
workpiece, and is ideal for removing paint or varnish
from large flat surfaces such as skirting boards,
doors, stairs etc. It should be used in conjunction
with a flat scraper. Vinyl tiles can be removed by
softening the tile and adhesive.
3)HOOK NOZZLE (15)
This nozzle disperses the heat flow evenly around
the whole workpiece. It is ideal for defrosting frozen
pipes, soldering pipe work, bending plastics and
heat-shrinking electrical parts.
4. STAND SUPPORTER USE (SEE FIG C, D)
This gun can be used in stationary mode.
1) Firstly fold down the Stand supporter (6).
2) Set the gun onto a level, stable workbench. Be
sure that the tool will not tip over.
3) Secure the power cord (8) to prevent
entanglement or pulling the gun off the
workbench.
4) Slide the start-stop switch (5) to position I or II by
selecting the required air flow.
5. LED LIGHT (SEE FIG. E)
Switching on:
To switch on, slide the LED light switch (9) up.
Switching off:
To switch off, slide the LED light switch (9) down.
MAINTENANCE AND
SERVICE
WARNING: Remove the plug before carrying
out any adjustment, servicing or maintenance.
Power cord replacement:
When it is necessary to replace the power cord,
it must be replaced by the manufacturer or its
agent in order to avoid danger to safety.
TROUBLESHOOTING
1. If your heat gun will not operate, check the power
at the power outlet.
2. If the outlet of the heat gun very hot, please rest
until cold.
3. If a fault can not be rectified return the tool to an
authorized dealer for repair.
After using for a long time, please don’t
turn off the machine immediately, adjust the
temperature to the minimum and run for a
period of time, which will help extend the
service life of the heating wire.
ENVIRONMENTAL
PROTECTION
Disposal
The machine, its accessories and
packaging materials should be sorted
for environmentally friendly recycling.
The plastic components are labeled for categorized
recycling.