Krell Industries EVOLUTION 222 страница 13 Скачать руководство пользователя | Manualshive

Страница: 13 / 48

background image

13

continued

SECTION

THREE

Quick Start

To access the full array of available functions for the Evolution 222, please read

this entire owner’s reference manual. The abbreviated routine in this Quick Start

section will allow you to connect and operate the Evolution 222 quickly and enjoy

its basic functions.

The front and rear panels are shown in the diagrams on pages 15 and 22. Each

button or feature is labeled with a callout number, and these numbers are shown

in parentheses in the sections below. (In the following instructions, the word “but-

ton” refers to a front panel operation, and “key” refers to a remote control opera-

tion.)

Connecting the Evolution 222 to Your System

Position the preamplifier where you intend to use it in your system. Do not

move the chassis after it is connected.

1.

Neatly arrange and organize wiring to and from the preamplifier and all com-

ponents. Separate the AC wires from any audio cables to prevent hum or other

unwanted noise from being introduced into the system.

2.

Connect the outputs of your source equipment to the appropriate CAST (18),

balanced (15), single-ended (16), or tape inputs (17) on the Evolution 222.

3.

Connect the main outputs (20) on the Evolution 222 to your amplifier’s inputs.

4.

Connect the supplied AC power cord to the IEC power cord receptacle (26) of

the preamplifier.

5.

Plug the other end of the AC power cord into AC power. The display (3) scrolls

through

EVOLUTION 222 SOFTWARE VERSION

, and the stand-by/power LED (7) illumi-

nates red, indicating that the Evolution 222 is in stand-by mode. When the

scrolling stops, the Evolution 222 is ready to be powered on.

Note

Use only the power cord provided with the preamplifier to make the connection to AC

power. Operation with a power cord other than the one supplied by Krell could induce

noise, limit current, or otherwise impair the ability of the preamplifier to perform optimally.

«
...
11
12
13
14
15
...
»

Содержание EVOLUTION 222

















































Отзывы:

Нет отзывов

Похожие инструкции для EVOLUTION 222

Бренд: NAD Страницы: 2

Бренд: Tube Amp Manufactur Страницы: 5

Stereo 25 MK II

Бренд: icon Audio Страницы: 8

Street Sweeper MkII

Бренд: SCIENCE Страницы: 14

Бренд: XINDAK Страницы: 10

AMP50 - XTR 1000

Бренд: W Audio Страницы: 8

Subamp SBA-12000

Бренд: Lynx Страницы: 12

Бренд: Teac Страницы: 48

Бренд: Toa Страницы: 12

Бренд: Radio Shack Страницы: 7

Бренд: t.amp Страницы: 10

Бренд: Toa Страницы: 12

Бренд: Custom Valve 50 Страницы: 14

Бренд: Crate Страницы: 4

Бренд: Atlona Страницы: 6

Бренд: Gemini Страницы: 9

Бренд: Adcom Страницы: 22

Бренд: Pyle Pro Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды