Krautzberger HS 25 Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 29

Krautzberger HS 25 Series Скачать руководство пользователя страница 21

6 Faults

Fault table

Spray pattern

Fault

Cause

Remedy

Normal flat jet spray pattern

Spray pattern too
heavy towards the top
and towards the
bottom

n

Soiled air nozzle

n

Soiled fluid nozzle

Clean nozzles (

5.2.1 „Clean hand held
spray gun“ on page 12

Spray pattern sharply
to the left or right side

n

Soiled air nozzle

n

Soiled fluid nozzle

Clean nozzles (

5.2.1 „Clean hand held
spray gun“ on page 12

Heavy application in
the centre of the spray
pattern

n

Too much fluid

n

Throttle fluid supply

n

Fluid too thick

n

Thin fluid

Split spray pattern

n

Too little fluid

n

Increase fluid supply

n

Flat jet air pres-
sure too high

n

Reduce flat jet air pres-
sure

Spray pattern too thin

n

Union nut loose

n

Tighten union nut

Fluid jet comes out in
spurts or flittering

n

Insufficient fluid
supply

n

Increase fluid supply

n

Blocked fluid path

n

Clean

n

Loose or dam-
aged fluid nozzle

n

Tighten or replace
(

Chapter 5.2.2

„Changing the air and
fluid noz-
zles“ on page 14

)

n

Worn needle seal

n

Change needle seal
(

Chapter 5.2.4

„Changing
seals“ on page 17

Leakage on the
clamping screw

n

Needle seal
defective

n

Change needle seal
(

Chapter 5.2.4

„Changing
seals“ on page 17

hand held spray gun HS-25

ENGLISH

HS-25, HS-25 HV1, HS-25 HV3

GB–21

«
...
19
20
21
22
23
...
»

Содержание HS 25 Series






























Отзывы:

Нет отзывов