Krautzberger HS 25 Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 29

Krautzberger HS 25 Series Скачать руководство пользователя страница 12

5 Maintenance

5.1 Maintenance schedule

The following sections describe the maintenance work that is required for optimal and fault-free
operation of the device.

Check wearing parts such as seals, nozzles and needles at regular intervals. The level of wear
depends on the abrasiveness of the spray fluid used. Escaping air and spray fluid as well as the
deterioration of the spray pattern are signs that parts are worn. In case of questions about mainte-
nance work and intervals, contact the manufacturer; see contact data on the last page.

Interval

Maintenance work

Personnel

After each use

Clean hand held spray gun (

Chapter 5.2.1 „Clean

hand held spray gun“ on page 12

)

Qualified personnel

When required Change fluid and air nozzle (

Chapter 5.2.2 „Changing

the air and fluid nozzles“ on page 14

Qualified personnel

Change fluid needle (

Chapter 5.2.3 „Changing the

fluid needle“ on page 15

Qualified personnel

Tighten needle seals (

Chapter 5.2.4 „Changing

seals“ on page 17

)

Qualified personnel

Change needle seals (

Chapter 5.2.4 „Changing

seals“ on page 17

)

Qualified personnel

5.2 Maintenance work

Clean the device before all maintenance work (

Chapter 5.2.1 „Clean hand held spray

gun“ on page 12).

5.2.1 Clean hand held spray gun

WARNING!

Danger of injury due to improper cleaning!

–

Observe the safety datasheets of the detergent manufacturer.

–

Do not immerse the hand held spray gun entirely in detergent.

Operating instructions

T-Dok-009-GB-Rev.0

[email protected], www.krautzberger.com

GB–12

«
...
10
11
12
13
14
...
»

Содержание HS 25 Series






























Отзывы:

Нет отзывов