Kramer VP-23RC
, Руководство пользователя

Страница: 16 / 57

KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your Presentation Switcher / Controller
12
Table 3: Rear Panel VP-23RC Presentation Switcher / Controller Features
# Feature Function
1 MIC IN Connector Connect to the microphone
2 COND. / DYN Selector Switch Push in to select a condenser, release to select a
dynamic microphone
3 CV OUT Terminal Block Connector Connect to the composite video balanced audio acceptor
4 Y/C OUT Terminal Block Connector Connect to the s-Video balanced audio acceptor
5 UXGA OUT Terminal Block Connector Connect to the VGA/UXGA balanced audio acceptor
6 MASTER OUT Terminal Block Connector Connect the master balanced audio channel acceptor
1
7 CV IN Terminal Block Connectors Connect to the composite video balanced audio sources
2
8 Y/C IN Terminal Block Connectors Connect to the s-Video balanced audio sources
2
9 UXGA IN Terminal Block Connectors Connect to the VGA/UXGA balanced audio sources
2
10
A
U
D
IO
SPKR OUT Terminal Block Connector Connect to a pair of loudspeakers
11 RELAY Terminal Block Connector Connect each relay
2
to a room item. The PINOUT is:
NO: Normally Open; C: Common; NC: Normally
Closed
12 IR Terminal Block Connectors Connect to an IR emitter cable (from IR1 to IR 3)
13 ETHERNET Connector Connects to the PC through computer networking
3
14 Port 1:Terminal Block
Connector (G, Rx, Tx)
4
15
RS-232
Ports
Port 2: 9-pin D-sub Connector
Connect to the RS-232 port of the A/V equipment or a
PC or other Serial Controller
16
C
O
N
TR
O
LL
E
R
PROGRAM Dipswitches DIP1 is for firmware upgrade (see section 10.2); DIP 3
is for factory reset; DIP 2 and DIP 4 are not used (see
section 7.1)
17 CV IN BNC Connectors Connect to the composite video sources
2
18 CV OUT BNC Connector Connect to the composite video acceptor
19 Y/C IN 4-pin Connectors Connect to the s-Video sources
2
20 Y/C OUT 4-pin Connector Connect to the s-Video acceptor
21 UXGA IN 15-pin HD Connectors Connect to the VGA/UXGA video sources
2
22 UXGA OUT 15-pin HD Connector Connect to the VGA/UXGA video acceptor
23
V
ID
E
O
UXGA CAT5 OUT
RJ-45 Connector
Connect to a remote computer graphics acceptor via
a receiver (for example, the TP-120 ), see section 3.2
24 RS-232 9-pin D-sub Port
Connect to a PC to control the
VP-23RC
25 FLASH PROG. Button Push in to upgrade the Presentation Switcher section to
the latest Kramer firmware (see section 10.1), or
release for Normal (the factory default)
26 RS-485 Terminal Block Port Pins B (-) and A (+) are for RS-485; Pin G may be
connected to the shield (if required)
27
S
W
IT
C
H
E
R
C
O
N
TR
O
L
Dipswitches DIPs 1, 2 and 3 are OFF, DIP 4 is ON for RS-485
termination
28 Power Connector with Fuse AC connector enabling power supply to the unit
1 Both the MASTER OUT and the SPKR OUT terminal block connectors receive the same signal: the MASTER OUT
outputs the signal as it is while the SPKR OUT is amplified
2 From 1 to 4
3 To configure the Media/Room Controller section or control the VP-23RC via the ETHERNET
4 Port 1 can connect to a PC to upgrade the firmware of the Media/Room Controller section