background image

Kramer Electronics Ltd. 

 

VM-10H2 

– Default EDID 

 

Default EDID 

Monitor 

  Model name............... VM-10H2 
  Manufacturer............. KMR 
  Plug and Play ID......... KMR1200 
  Serial number............ n/a 
  Manufacture date......... 2016, ISO week 14 
  Filter driver............ None 

  

-------------------------  

  EDID revision............ 1.3 
  Input signal type........ Digital 
  Color bit depth.......... Undefined 
  Display type............. Monochrome/grayscale 
  Screen size.............. 520 x 320 mm (24.0 in) 
  Power management......... Standby, Suspend, Active off/sleep 
  Extension blocs.......... 1 (CEA-EXT) 

  

-------------------------  

  DDC/CI................... Not supported 

 

Color characteristics 

  Default color space...... Non-sRGB 
  Display gamma............ 2.20 
  Red chromaticity......... Rx 0.674 - Ry 0.319 
  Green chromaticity....... Gx 0.188 - Gy 0.706 
  Blue chromaticity........ Bx 0.148 - By 0.064 
  White point (default).... Wx 0.313 - Wy 0.329 
  Additional descriptors... None 

 

Timing characteristics 

  Horizontal scan range.... 30-83kHz 
  Vertical scan range...... 56-76Hz 
  Video bandwidth.......... 170MHz 
  CVT standard............. Not supported 
  GTF standard............. Not supported 
  Additional descriptors... Established timings 
  Preferred timing......... Yes 
  Native/preferred timing.. 1920x1080p at 60Hz  

    Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync 

 

Standard timings supported 

    

 

640

 

x  480p at  60Hz - IBM VGA 

    

 

640

 

x  480p at  72Hz - VESA 

    

 

640

 

x  480p at  75Hz - VESA 

    

 

800

 

x  600p at  60Hz - VESA 

    

 

800

 

x  600p at  72Hz - VESA 

    

 

800

 

x  600p at  75Hz - VESA 

   

 

1024

 

x  768p at  60Hz - VESA 

   

 

1024

 

x  768p at  70Hz - VESA 

   

 

1024

 

x  768p at  75Hz - VESA 

   

 

1280

 

x 1024p at  75Hz - VESA 

   

 

1600

 

x  900p at  60Hz - VESA STD 

   

 

1280

 

x  800p at  60Hz - VESA STD 

   

 

1600

 

x 1200p at  60Hz - VESA STD 

   

 

1024

 

x  768p at  85Hz - VESA STD 

    

 

800

 

x  600p at  85Hz - VESA STD 

    

 

640

 

x  480p at  85Hz - VESA STD 

   

 

1152

 

x  864p at  75Hz - VESA STD 

   

 

1280

 

x  960p at  60Hz - VESA STD 

    

 

848

 

x  480p at  60Hz - VESA 

   

 

1280

 

x  768p at  60Hz - VESA 

   

 

1280

 

x 1024p at  60Hz - VESA 

   

 

1360

 

x  768p at  60Hz - VESA 

   

 

1440

 

x  900p at  60Hz - VESA 

   

 

1400

 

x 1050p at  60Hz - VESA 

   

 

1650

 

x 1050p at  60Hz - VESA 

 

EIA/CEA-861 Information 

  Revision number.......... 3 
  IT underscan............. Supported 
  Basic audio.............. Supported 
  YCbCr 4:4:4.............. Not supported 
  YCbCr 4:2:2.............. Not supported 
  Native formats........... 1 
  Detailed timing #1....... 720x480i at 30Hz  

    Modeline............... "720x480" 8.490 720 808 857 981 480 488 498 570 inthsync +vsync 

  Detailed timing #2....... 852x480p at 60Hz (16:9) 
   

  Modeline............... "852x480" 49.450 852 1380 1429 1572 480 484 489 525 +hsync +vsync 

Содержание VM-10H2






























Отзывы: