background image

 

VA-8xl - Operating the VA-8xl 

 

Operating the VA-8xl  

When switching on the 

VA-8xl

 (after a previous session), the

 

VA-8xl

 briefly scans 

each channel (stored in the non-volatile memory), showing the settings in the LED 
displays. After that, the 

VA-8xl

 goes to channel 1, and shows its gain/attenuation 

level in dB. 

During regular work, the 

VA-8xl

 shows the status of the last channel you observed 

and/or changed. 

To observe the status of a channel: 

 

Press a CHANNEL SELECTOR button. 
That CHANNEL SELECTOR button illuminates for about 20 
seconds and the

 

decibel values of the selected channel appear in 

the dimmed LED displays 

When the LEDs are dimmed, you cannot change the gain or attenuation - the values 

are for observation only 

You can control the amplifier gain of the left and right channels via the front panel 
buttons, or remotely via RS-232 or RS-485. You can increase or decrease the gain 
in increments of 0.5dB from -95dB up to +31dB. 

You can control the amplifier gain of the left and/or right channels separately or 
together (see 

Section  5.1

). 

5.1 

Adjusting the Gain/Attenuation of the Channels 

To adjust the amplifier gain or the attenuation: 

1.  Press the appropriate CHANNEL SELECTOR button. 

That CHANNEL SELECTOR button illuminates and the

 

decibel values of the 

selected channel appear in the dimmed LED displays (stored in the 
non-volatile memory). 

(When the LEDs are dimmed, you cannot change the gain or attenuation - the values 

are for observation only). 

2.  Press the LEFT LEVEL and/or the RIGHT LEVEL button. 

The

 

decibel values of the selected channel appear in the bright LEFT and/or 

RIGHT LED display. 

Содержание VA-8XL


































Отзывы: