Kramer Cobra R1300A Скачать руководство пользователя страница 6

Страница: 6 / 20

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Setup and Installation

4 Setup and Installation

4.1 Data Mode Configuration

The serial signal is 3 wire TX, RX, GND and does not support full modem

signals. Baud rates for the S2 series are fixed at 9600. Simplex modes are

supported without jumper or other changes by simply using the TX signal only.

S2 units require no configuration.

4.2 Making the Connections

This section contains figures showing connections with the specific

Cobra

R1300A / R1300S2 / R1300S2M

series models. In general, however, the

connection and setup procedure at both transmitter and receiver ends is as

follows:
NOTE: all units must be the same type for all supported features to function

correctly. For example, a

Cobra

transmitter set for R/L summed audio must be

connected to an

R1300A / R1300S2 / R1300S2M

set for R/L summed audio.

Similarly, a

Cobra

cannot be used with an

R1300A / R1300S2 / R1300S2M

Video modes may function normally, but 4th pair options will not.
At the transmitter end (refer to the transmitter user guide):

1. Connect the source video to the

Cobra

Series transmitter video input port,

which is an HD15 connector labeled SOURCE IN or VIDEO IN.

2. If desired, attach a local monitor via the local monitor port to LOCAL

OUT.

3. Make your audio/serial connections via the audio connector or DB9

connector as appropriate.

4. Connect the CAT 5 cable to the transmitter.
5. Apply power on the transmitter. The LED should light and, if there is a local

monitor attached, a video image should appear on the monitor’s screen.

At the receiver end:

1. Connect the VIDEO OUT HD15 connector to the display unit and attach

any audio (AUDIO/AUX I/O) or serial connections (RS-232) depending on

the model of the

Cobra

CAT 5 Video System.

2. Connect the CAT 5 cable to the LINK INPUT connection. If daisy chaining

units, connect the output CAT 5 cable to the LINK OUTPUT connection.

3. Apply power. The LED should light and video should appear on the display

(make sure that the display is powered ON).

4. Adjust video levels and skew compensation.
5. Mount the

R1300A / R1300S2 / R1300S2M

in a location that ensures the

ventilation holes and fan are not blocked.

Содержание Cobra R1300A





















Результаты поиска

Содержание Cobra R1300A

Отзывы:

Бренды по названию

Популярные бренды

Kramer Cobra R1300A, Руководство пользователя

Результаты поиска

Содержание Cobra R1300A

Отзывы:

Бренды по названию

Популярные бренды