Kramer Cobra R1300A Скачать руководство пользователя страница 18

Страница: 18 / 20

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Technical Specifications

6 Technical Specifications

Table 6: Technical Specifications

of the Cobra R1300A, Cobra R1300S2

CABLE REQUIRED:

Category 5, 5e, 6 shielded or unshielded twisted pair

COMPLIANCE:

CE; FCC Class A, IC Class/class A

VIDEO SUPPORT:

all supported VESA modes to WUXGA (1920x1200), RGBHV, RGB,
Composite (NTSC, PAL, SECAM), S-Video, Component Video,
widescreen modes, HDTV modes including 1080p, 1080i, 720p

RESOLUTION AND REFRESH

RATE:

At 1300 ft. or less: a maximum of 1920x1200 to 60 Hz

REQUIRED SOURCE IMPEDANCE: Video OUT: 75 ohms;

Audio OUT (if any): 600 ohms maximum

REQUIRED DESTINATION

IMPEDANCE:

Video IN: 75 ohms;
Audio models: Audio IN (if any): 600 ohms minimum

AUDIO CHARACTERISTICS:

R1300A

: Right/Left summed

R1300S2

: Full Stereo

Line Level 600 Ohm Unbalanced

SERIAL CHARACTERISTICS:

3 wire, fixed baud rate of 9600

CONNECTORS:

(1) 4 pin terminal block, (2) RJ-45, (1) HD15 F; (1) DB9M (model

dependent)

TEMPERATURE TOLERANCE:

Operating: 32 to 104°F (0 to 40°C);

Storage: -4 to +140°F (-20 to +60°C).

HUMIDITY TOLERANCE:

Up to 80% noncondensing

ENCLOSURE:

Steel

POWER:

+5 VDC @ 260 mA max
Consumption: 6 watts maximum

SIZE:

1.2" H x 4.1" W x 5.5" D (3.0 x 10.4 x 14.0 cm)

WEIGHT:

1.0 lb. (0.45 kg)

1 Specifications are subject to change without notice

Содержание Cobra R1300A





















Результаты поиска

Содержание Cobra R1300A

Отзывы:

Бренды по названию

Популярные бренды

Kramer Cobra R1300A, Руководство пользователя

Результаты поиска

Содержание Cobra R1300A

Отзывы:

Бренды по названию

Популярные бренды