background image

 

RC-76R/RC-78R - Introduction

 

 

Introduction 

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been 
providing a world of unique, creative, and affordable solutions to the vast range of 
problems that confront video, audio, presentation, and broadcasting professionals 
on a daily basis. In recent years, we have redesigned and upgraded most of our 
line, making the best even better!  

Our 1,000-plus different models now appear in 11 groups that are clearly defined 
by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers; 
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5: 
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7: 
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9: 
Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11: 
Sierra Products; GROUP 12: Digital Signage; GROUP 13: Audio; and GROUP 14: 
Collaboration. 

Congratulations on purchasing your Kramer 

RC-76R/RC-78R 

Room Controllers

which are ideal for the following typical applications: 

 

Convenient control of complex multimedia systems and other room facilities 
such as screens, lighting and shades in auditoriums and meeting rooms 

 

 

 

Содержание 2900-300253

























Отзывы: