manualshive.com logo in svg

KRAL CLC 55, Руководство по эксплуатации, Страница: 23 / 38

Поделиться
Скачать
KRAL CLC 55 Скачать руководство пользователя страница 23

Operating Instructions

OIC 12en  Edition 08/2016 

23

Commissioning

Operation

1. Switch on the power supply and then turn it off again immediately.
2. Compare the direction of rotation of the fan impeller with the rotation-direction arrows on the pump 

flange.

3. If the directions do not match, swap over two electrical connection phases. Repeat Steps 1 and 2.

Commissioning the pump

Requirements:

□

Pump set up and connected correctly

□

Motor connected correctly

□

Pipe system is free of impurities

□

Sealing chambers A, B and C filled with PTFE grease/quench liquid

□

Pump filled with pumped liquid

□

Shut-off devices in the suction and pressure line opened

□

Variant 3: Circulation line opened for quench liquid

1

Rotation-direction arrow

Fig. 6

Indication of direction of rotation

1

1

CAUTION

Dry running can damage pump equipment.

► Ensure that the pump is filled properly.
► Switch the pump on for a maximum of 1 second and then off again immediately.

WARNING

Risk of injury through rotating parts.

► Ensure that the coupling protection is mounted.

WARNING

Risk of injury through emitted pumped liquid.

► Wear protective equipment during all the work.
► Ensure that all the connections are connected sealingly.

CAUTION

Dry running can damage pump equipment.

► Ensure that the pump is filled properly.
► If the pump does not deliver after 10 – 15 seconds, abort commissioning.

Содержание CLC 55







































Отзывы:

Нет отзывов