Kraissmann 370 SB 13/16, Руководство пользователя

Страница: 8 / 16

8 |
English
tightly with the screw.
Finally, fit the complete bit head to the pillar. Align the
head so that it is horizontal to the base plate and fasten
it in position with the screws.
Screw the 3 supplied handles in the handle mounts.
Screw in the speed control lever.
Secure the roller support with thumb screws.
Before you mount the drill chuck with the MK shank,
check that both parts are clean. Insert the taper mandrel
in the taper of the drill chuck with a powerful jolt. Then
insert the taper in the spindle. To do this, place the drill
chuck with taper in the spindle and guide it to the stop
point, then turn the chuck until it slips a little further
into the spindle. Insert the drill chuck with taper into the
spindle with a jolt and check that the chuck is secure.
Important:
All bare parts are greased in order to protect them from
corrosion. Before mounting the drill chuck onto the spin
-
dle, both parts must be completely degreased using an
environmentally friendly solvent. This ensures optimal
transmission of power.
Installing the machine
Before you use the drill for the fi rst time it must be
mounted in a stationary position on a fi rm surface.
Use both mounting holes in the base plate to do this. En
-
sure that the machine is freely accessible for operation,
adjustment and maintenance.
Important:
The fixing screws may only be tightened to a point where
they do not distort or deform the base plate. Excessive
tension can lead to fracture.
Folding chip guard
Mount the folding chip guard. The height of the cover is
infi nitely adjustable and can be locked using both thumb
screws.
The chip guard can be fl ipped up to enable bits to be
changed.
Prior to starting
Ensure that the voltage of the mains supply complies with
the specifi cations on the rating plate.
Connect the machine only to a socket with the properly
installed earthing contact.
The table drill is equipped with a no-volt trip that is de
-
signed to protect the operator from an undesired restart
following a drop in voltage. Should this occur, the ma
-
chine must be manually restarted.
OPERATION
General
To switch on the machine, push in the green On button “I”
; the machine starts up. To switch off , press the red Off
button “O”; the device shuts down.
Ensure that you do not overload the device. If the sound
of the motor drops in pitch during operation, it is being
overloaded.
Do not overload the device to the point where the motor
comes to a standstill. Always stand in front of the ma
-
chine during operation.
Inserting the tool
Make sure that the power plug is removed from the
socket-outlet before changing tools. Only cylindrical
tools with the stipulated maximum shaft diameter may be
clamped in the scroll chuck. Only use a tool that is sharp
and free of defects. Do not use tools whose shaft is dam
-
aged or which are deformed or fl awed in any other way.
Use only accessories and attachments that are specifi ed in
the operating instructions or have been approved by the man
-
ufacturer. If the pillar drill should become jammed, switch
off the machine and return the drill to its starting position.
Handling the keyless chuck
Your pillar drill is equipped with a keyless chuck. This
enables tools to be changed without the need for an ad
-
ditional chuck key. To do so, insert the tool in the quick-
change drill chuck and tighten by hand.
Setting the speed
The operating speed of the machine is infi nitely adjust -
able.
Important!
▶ Speed adjustments are allowed only when the motor
is running.
▶ Slowly and steadily move the speed control lever
while the machine is in idle mode.
▶ Ensure that the machine can run without interruption
(i.e. remove workpieces, drill bits, etc.).
Use the speed control lever to infi nitely adjust the
speed.
Important!
Never let the drill press run when the V-belt cover is
open. Always pull power plug before opening the cover.
Never touch the V-belt when it is rotating.
Drill depth stop
The drilling spindle has a swivelling scale ring for setting
the drill depth. Only adjust the setting when the machine
is at a standstill.
▶ Press the drilling spindle downwards until the tip of
the drill bit touches the workpiece.
▶ Turn the scale ring all the way down.
▶ Turn the scale ring up by the distance of the desired