manualshive.com logo in svg

Kraft Powercon PRX3, Руководство пользователя

Поделиться
Скачать
Kraft Powercon PRX3 Скачать руководство пользователя страница 10

9 

KraftPowercon Sweden AB, Hjalmar Petris väg 49, S-352 46  Växjö, Sweden, Tel: +46 470-705200, Fax: +46 470-705201, 

www.kraftpowercon.com

Ripple current................................................. <1 % of rated current 

Efficiency, typical .......................................... >92 % at 3x400 V

AC 

Other, see table in section 3.1 

ASSORTMENT

. 

3.3

ENVIRONMENTAL DATA 

Class of enclosure ......................................................... IP21 as per EN 60529 

Cooling............................................................................ Temperature controlled fans in rectifier 

modules, otherwise natural convection 

Ambient temperature .................................................. 0 to +40 °C 

Storage temperature..................................................... -40 to +70 °C 

Humidity ........................................................................ <90 % RH, non-condensed 

Altitude a.s.l................................................................... <2000 m 

Noise level at +20 °C, 25% load ................................. 50-58 dBA depending on number of rectifier 

modules

3.4

MECHANICAL DATA 

Design ....................................... Floor cabinet with 19” rack frame 

Placement ................................. Standing on floor indoors in dry and clean area 

Weight ....................................... See table in section 3.1 

ASSORTMENT

 . 

Dimensions .............................. Cubicle type F27: 1361/600/600 mm (h/w/d), 

Cubicle type F41: 2053/600/474 mm (h/w/d), 
Cubicle type S39: 2100/840/654 mm (h/w/d), 

see also layout drawing 

Appendix A

Colour ....................................... RAL 7035 light grey 

Cable inlet ................................ From above or beneath (F27, F41) 

From beneath, above as option (S39) 

3.5

CONFORMITY WITH STANDARDS 

EN 60529 ................................ Protection degree IP21 
EN 50178 ................................ LVD. Electronic equipment, including power electronics in electrical 

power installations. 

EN 50272-2 ............................ Safety requirements for secondary batteries and battery installations 

EN 61000-6-2 ......................... EMC. Immunity of equipment in an industrial environment 

EN 61000-6-4 ......................... EMC. Emission from equipment in an industrial environment 

Содержание PRX3








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды