1 1
OPERATING HEATER
FOR YOUR SAFETY
GFN4227R,GFP4228R Series Models
A. This appliance has a pilot which
must be lighted by control system,
W hen lighting the pilot, follow
t h e s e i n s t r u c t io n s e xa c t ly .
B . B E F O R E L IG H T IN G sm ell all
around the appliance area for
gas. Be sure to smell next to the
floo r b ec au se som e g as is
heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS
CAUTION:
Do not try to adjust
h eatin g levels b y using th e
equipment shutoff valve.
1. STOP! Read the safety information,
page 2.
2. Make sure equipment shutoff
valve is fully open.
Note: If operating by remote control,
you must set the Control Knob on
ELECTRIC position.
Do not set the control knob between
the locked position, otherwise there
will be no power to the heater.
Note:
Please wait one minute after
shutting off fireplace to allow the
electronic module to reset before
starting again.
Note:
To operate your heater the ON/
OFF switch on front of heater must be
in the ON position. The RED light on
the front of heater indicates there is
electrical power to your heater when
the ON/OFF switch is in the ON po-
sition. The GREEN light on the fr-
ont of heater indicates the pilot light
is ON. (See Figure 11)
WARNING:
If you do not
follow these instructions exactly, a
fire or explosion may result causing
property damage, personal injury or
loss of life.
NOTICE:
During initial operation
of new
fireplace
, burning logs will
give off a paper-burning smell. Or-
ange flame will also be present.
Open a window to vent smell. This
will only last a few hours.
Do not try to light any appliance.
Do not touch any electrical switch;
do not use any phone in your
building.
Immediately call your gas sup
plier from a neighbor
’
s phone.
Follow the gas supplier
’
s
instructions.
If you cannot reach your gas
supplier, call the fire department.
C. Use only your hand to push in
control knob. Never use tools. If the
the appli ance could not operate , don't
try to repair it, Call a qualified service
technician or gas supplier.Forced or at-
tempted re-pair may result in a fire or
explosion.
D. Do not use this appliance if any
part has been under water. Imme-
diately call a qualified service techni-
cian to inspect the appliance and to
replace any part of the control system
and any gas control which has been
under water.
Function of power ON/OFF swith.
LIGHTING INSTRUCTIONS
Figure 11 - ON/OFF Switch location
OPERATIONS OF
REMOTE TRANSMITTER
1. Install three AAA batteries in the
battery holder. The initial start-up on
the LCD is: SET TEMP is 85
°
F,
ROOM TEMP is 85
°
F, and fan is on
“
AUTO
”
select.
Fig 12 Initial start-up display
2. When in operation, point the
remote transmitter to the remote
receiver on the front of fireplace at
a maximum distance of 20 feet
without any obstruction between
them.
OPERATIONS OF
BURNER
1. Before plugging into the outlet
make sure that the appliance is
connected to the gas supply. Plug
fireplace into a properly grounded
120 Volt, 60Hz, 15 amp outlet. You
will hear a high pitch sound and
power light(red) on the door will
be lit that indicates that the
burner is ready to be operated.
2. Point the remote transmitter to
the burner. Press IGN/OFF button,
the electric spark starts igniting
the pilot and then the burner. Wait
five (5) minutes to clear out any
air. If you smell gas. STOP!
Please check the gas connection.
The green operation light on the
front of fireplace will be lit when
pilot and burner are on.
Note:
The main burner does not
respond immediately to the set
temperature until about one
minute later.
3. To shut off, press IGN/OFF button
on remote or on front of fireplace.
Note:
The pilot will also shut off.
11