manualshive.com logo in svg
background image

10.0  OPERATING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

 

SECTION 10

  OPERATING INSTRUCTIONS

#SFD-36

R.6  February 2022

46

HUSSONG MFG. CO., INC.

KOZY HEAT FIREPLACES

WARNING

Do not operate appliance with the glass front removed, cracked, or 

broken. Replacement of the glass should be done by a licensed or 

qualified service person.
Under no circumstances should any solid fuel (wood, coal, paper, 

cardboard, etc.) be used in this appliance.
Children and adults should be alerted to the hazards of high surface 

temperature and should stay away to avoid burns or clothing ignition.

CAUTION

Clothing or other flammable material should not be placed on or near 

the appliance.
Young children should be carefully supervised when they are in the 

same room as the appliance. Toddlers, young children and others 

may be susceptible to accidental contact burns. A physical barrier is 

recommended if there are at risk individuals in the house. To restrict 

access to a fireplace or stove, install an adjustable safety gate to keep 

toddlers, young children and other at risk individuals out of the room 

and away from hot surfaces.

WARNING: 

If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

1. 

STOP! Read all the safety information above on this page. 

2. 

Press the wireless remote POWER button. 

3. 

Turn off all electric power to the appliance. 

4. 

This appliance is equipped with an ignition device which 

automatically lights the pilot. Do not try to light the pilot by 

hand.

5. 

Locate the manual valve installed by your qualified service 

technician.

6. 

Turn the manual valve clockwise 

 to the OFF position. 

7. 

Wait five (5) minutes to clear out any gas. Then, smell 

for gas, including near the floor. If you smell gas, STOP! 

Follow ‘B’ in the safety information above. If you do not smell 

gas, go to the next step. 

8. 

Turn the manual valve counterclockwise 

 to the ON position. 

9. 

Turn on all electric power to the appliance. 

10. 

Press the wireless remote POWER button. 

11. 

If the appliance will not operate, follow the instructions, “To 

Turn Off Gas To Appliance” and call your service technician or 

gas supplier. 

OPERATING INSTRUCTIONS

A. 

This appliance is equipped with an ignition device which 

automatically lights the pilot. Do not try to light the pilot by 

hand. 

B. 

BEFORE OPERATING

 smell around the appliance area for gas. 

Be sure to smell next to the floor because some gas is heavier 

than air and will settle on the floor. 
WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electric switch; do not use any phone in 

your building.

•  Immediately call your gas supplier from a neighbor’s phone. 

Follow the gas supplier’s instructions. 

•  If you cannot reach your gas supplier, call the fire 

department. 

C. 

Use only your hand to turn the gas control manual valve. Never 

use tools. If the valve will not turn by hand, do not try to repair 

it; call a qualified service technician. Force or attempted repair 

may result in a fire or explosion. 

D. 

Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect the 

appliance and to replace any part of the control system and 

any gas control that has been under water. 

1. 

Press the wireless remote POWER button.

2. 

Turn off all electric power to the appliance if service is to be 

performed. 

3. 

Locate the manual valve installed by your qualified service 

technician.

4. 

Turn the manual valve clockwise 

 to OFF position. 

FOR YOUR SAFETY READ BEFORE OPERATING

ON

OFF

POWER

ON/OFF

NOTE

When this fireplace is initially lit, condensation will appear on the glass. This is normal in all gas fireplaces and will disappear after several 

minutes. A paint smell will occur during the first few hours of burning. It is recommended to leave the fan off during this period to help speed 

the paint curing process. 
This fireplace may produce noises of varying degree as it heats and cools due to metal expansion and contraction. This is normal, and does not 

affect the performance or longevity of the fireplace.

Содержание SPRINGFIELD 36































































Отзывы: