background image

#BAY-41-MV R.1 July 2021

Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces

VENTING 

33

7.2  Approved Vent Systems

This appliance is equipped for use with a 4” exhaust by 6-5/8” air 

intake co-axial vent pipe system.
This appliance is approved for use with Kozy Heat 4” x 7” #700 Series 

Flexible Direct Vent system (horizontal terminations only). Refer to 

Section 7.8 #700-2 Series Direct Vent Termination Kit(s) on page 29 for 

venting components and installation instructions. 
This appliance is approved for use with manufacturers (horizontal and 

vertical terminations): American Metal Products (Ameri-Vent), BDM, 

ICC, Metal Fab*, Olympia Chimney Supply, Inc., Selkirk, and Simpson 

DuraVent.

*WHEN INSTALLING METAL FAB VENT SYSTEM 

with this appliance 

an adapter must be used. Use adapter part number 4DDA. 

The following termination caps are not allowed:

 Metal-Fab 4DH7, and 

Simpson Duravent Snorkel 46DVASNK14.
This appliance can be adapted to use 4” diameter aluminum flexible 

pipe when used in combination with an existing minimum 6” x 8” ID 

masonry or an existing minimum 7” ID Class A metal chimney. See 

Section 7.6 Class A Chimney/Masonry Chimney Conversion Kit on 

page 42.
This appliance can be adapted to use 3” x 3” flexible co-linear vent 

pipes when used in combination with an existing minimum 6” x 8” ID 

masonry or 7” ID Class A metal chimney. See Section 7.7 Coaxial to Co-

Linear Chimney Conversion on page 43.
The vent configurations listed in this manual are shown with rigid 

pipe. Flexible pipe may be used for approved venting configurations 

by approved vent manufacturers. Refer to the vent manufacturer’s 

installation instructions.
Refer to the vent manufacturer’s installation manual for complete 

installation instructions. Vent installation must conform with venting 

requirements and restrictions as outlined in this manual.

7.3  Venting Requirements

Consult the local and national installation codes to assure adequate 

combustion and ventilation air is available. Venting requirements 

apply to both natural gas and propane.
NOTE: Wall thimble products that comply with the required clearance 

to combustibles must be installed for all horizontal vent runs that pass 

through interior or exterior walls. These wall thimble products may be 

insulated using unfaced insulation products listed as noncombustible 

per ASTM E 136.
NOTE: Attic insulation shields may be insulated using unfaced 

insulation products listed as noncombustible per ASTM E 136.

• 

Flame height and appearance will vary depending upon venting 

configuration and the type of fuel used.

• 

Refer to the vent manufacturer’s installation manual for 

complete installation instructions. Vent installation must 

conform with venting requirements and restrictions as outlined 

in this manual.

• 

Provide a means for visually checking the vent connection to the 

appliance after the fireplace is installed.

• 

A minimum of 1” (25mm) clearance on all side of the vertical pipe 

must be maintained. 

• 

A minimum of 1” (25mm) clearance on all sides of the horizontal 

vent flex pipe must be maintained.

• 

A minimum of 1-1/2” (38mm) top clearance and a minimum of 1” 

(25mm) bottom and side clearances for the horizontal rigid pipe 

must be maintained.

Содержание BAY-41-MV






























































Отзывы: