kozy heat BAY-36-L страница 11 Скачать руководство пользователя | Manualshive

Страница: 11 / 51

background image

FRAMING

11

3.0 FRAMING

3.1 Appliance Placement

Considerations

WARNING: Due to high temperatures, the appliance should be
located out of traffic and away from furniture and draperies.
FIRE HAZARD: Do NOT install this appliance directly on
carpeting, vinyl, or any other combustible material other than
wood.

• This appliance must be installed on a level surface capable

of supporting the fireplace and venting. If possible, place the
fireplace in a position where the vent terminates between two
studs, eliminating the need for any additional framing.

• This fireplace may be installed in a bedroom.
• Please be aware of the large amount of heat this fireplace will

produce when determining a location.

3.2 Stand-off Assembly and Installation

WARNING: The top stand-offs provide the 10 in (254 mm)
minimum clearance to the header. Use only non-combustible
material in this area for the entire width of the fireplace. DO
NOT use wood, sheetrock, et cetera, in this zone.
Top stand-off brackets must be formed and attached prior to
positioning fireplace into framed opening.
NOTE: If installing trim kit assembly #B36-FTK, please refer
to Section 4.3 Optional Trim Kit Assembly #B36-FTK on page
17 before installing stand-offs.

1. Remove and save (4) screws securing stand-off heat shields

and stand-off brackets on top of the fireplace.

2. Form each top stand-off bracket by bending at perforations,

as shown.

3. Align the holes in the formed top stand-offs with the holes

in the fireplace top. Secure with the (4) screws previously
removed along with (4) screws located on top of the
fireplace.

4. Form stand-off heat shields as shown. The flange will face up

and to the back of the fireplace.

5. Align the in the stand-off heat shields with the holes in the top

stand-off brackets. Secure with (8) screws provided in the
fireplace components packet.

Figure 3.1, Stand-off Assembly and Installation

STAND-OFF BRACKETS AS SHIPPED

BEND AT
PERFORATIONS

FORMED
STAND-OFF

STAND-OFF HEAT SHIELDS INSTALLED

«
...
9
10
11
12
13
...
»

Содержание BAY-36-L




















































Отзывы:

Нет отзывов

Похожие инструкции для BAY-36-L

Бренд: Vanguard Страницы: 32

Cleveland CMSF-1/0310

Бренд: Warm House Страницы: 19

Oakville Series

Бренд: Napoleon Страницы: 72

Бренд: Napoleon Страницы: 4

Бренд: Valor Страницы: 12

Бренд: Napoleon Страницы: 48

Бренд: Napoleon Страницы: 4

Бренд: Napoleon Страницы: 20

Allure Vertical Series

Бренд: Napoleon Страницы: 120

Бренд: Napoleon Страницы: 4

Бренд: Paloform Страницы: 18

Бренд: Pacific energy Страницы: 24

Бренд: Solas Страницы: 6

Бренд: Bronpi Страницы: 81

Ascent Linear BL56

Бренд: Napoleon Страницы: 132

REGENT FRLC EN Series

Бренд: Flavel Страницы: 31

Бренд: Empire Comfort Systems Страницы: 20

Black Beauty Radiant 340

Бренд: Valor Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды