Koyker KB660 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 44

Koyker KB660 Скачать руководство пользователя страница 40

CYLINDER GLAND SERVICE DIAGRAM

CYLINDER PISTON SERVICE DIAGRAM

Page 38

To Install Seals:

1. Thoroughly clean piston sealing surface of all
foreign matter.

2. Heat new seals in hydraulic oil to 160

°

F.

Never use a direct flame or heated water on
hydraulic seals.

3.  Remove seals from oil, wipe dry and install in
       piston grooves as shown in illustration at left.
       Be sure seals have completely seated in
       piston grooves before allowed to cool.

4.  Replace piston on cylinder shaft and assemble
       cylinder when seals have cooled to room
       temperature.

To remove seals

Carefully cut across each seal with a sharp knife.  Be sure
not to scratch sealing surfaces of aluminum piston.  If a
sharp knife is not available.  An electric soldering gun or
hot iron may be used to melt throughout seals

All gland seals shown with a section removed

to facilitate correct installation.

Note: To install rod wiper and EZ-squeeze seal,
fold similar to shape shown below, slip into
gland bore and locate each in its respective
groove. Tools are used to fold seals, take care
not to damage sealing surfaces.

Important! Be sure all gland and piston seals have been installed
correctly before cylinder is assembled!

O-RING

EZ SQUEEZE SEAL

ROD WIPER

BACK UP

GLAND

SECTION VIEW

ASSEMBLED GLAND

SECTION VIEW

ASSEMBLED PISTON

EZ SQUEEZE SEAL

PISTON

EZ SQUEEZE SEAL

O-RING

ROD WIPER

BACK UP

GLAND

EZ SQUEEZE SEAL

O-RING

O-RING

EZ SQUEEZE SEAL

PISTON

EZ SQUEEZE SEAL

«
...
38
39
40
41
42
...
»

Содержание KB660













































Отзывы:

Нет отзывов