background image

11

WARRANTY

The item meets the safety requirements as set forth by applicable regulatory references.

 Control unit warranty service life: 12 months from the date of sale through a retail network.

 Control unit service life — 5 years minimum.

 

CAUTION! 

If the Operating Manual has no date of sale and retailer stamp, the warranty period will 

be calculated from the date of manufacture.

 The  control  unit  shall  be  shipped  in  the  original  package.  Violation  of  this  condition  releases  the 
manufacturer from any claims as to mechanical damages incurred during shipment.

 Any defects ascribed to the manufacturer will be remedied free of charge.

 

CAUTION!

  No  claims  as  to  the  item's  performance  will  be  accepted,  and  no  warranty  repairs  or 

replacements will be done in the following cases:

- The defect is caused by negligent handling

- The user did not follow the installation, operation, and maintenance instructions

- The user or a third party stored or transported the item in an improper manner

- The item was not used for its intended purpose

- The item was repaired by the user or a third party without proper qualification

- The warranty period has expired

 

CAUTION!

 The manufacturer reserves the right to make changes to the design of the control unit 

provided these changes do not adversely affect the item's consumer properties.

 

 

TRANSPORT AND STORAGE

 

The control unit's dimensions and weight allow shipment by any transport. If needed, the control unit 
can be uninstalled and transported to another place of operation or storage.

If the item was transported at negative temperatures, keep it in the original packaging at a normal 
temperature for at least three hours.

  

DISPOSAL

 

Control units that became inoperable through improper operation, failures, or expired service life shall 
be disposed of.

The control unit contains no environmentally hazardous materials or accessories, and therefore can be 
disposed of in a regular way.

SAUNA HEATERS, GARDEN FIRE PITS, SOLID FUEL BOILERS

Содержание EOS-CONTROL 18

















Отзывы: