Korg NAUTILUS Series, Руководство по параметрам, Страница: 615 / 961

SAMPLING: Page Menu Commands 9–5: TFX2
605
SAMPLING: Page Menu Commands
Delete Sample → p.606
Copy Sample → p.606
Rename Sample → p.606
Move Sample → p.607
Sample Mono To Stereo (Change Sample Type) → p.607
Delete MS (Delete Multisample) → p.608
Copy MS (Copy Multisample) → p.608
Rename MS (Rename Multisample) → p.608
Move MS (Move Multisample) → p.608
Convert MS (Multisample) To Program → p.609
MS Mono To Stereo/MS Stereo To Mono
(Change Multisample Type)
→ p.610
Optimize RAM → p.114
Select Directory/File for Sample To Disk → p.115
Auto Sampling Setup → p.611
Truncate (for Sample Edit) → p.613
Cut → p.614
Clear → p.614
Copy → p.615
Insert → p.615
Mix → p.615
Paste → p.616
Insert Zero → p.616
Normalize/Level Adjust → p.617
Volume Ramp → p.617
Rate Convert → p.618
Reverse → p.618
Link → p.619
Truncate (for Loop Edit) → p.620
Time Slice → p.620
Time Stretch → p.625
Crossfade Loop → p.629
Pitch BPM Adjust → p.629
Copy Insert Effect → p.122
Swap Insert Effect → p.122
Insert IFX Slot → p.122
Cut IFX Slot → p.123
Clean Up IFX Routings → p.124
Copy MFX/TFX → p.125
Swap MFX/TFX → p.125
Write FX Preset → p.125
PAGE → p.126
MODE → p.126
Remarks on editing stereo
samples
• For stereo samples, the L channel and R channel samples
are edited simultaneously. If you wish to edit only the L
channel or R channel, select a mono multisample, and
select either the L channel or R channel sample for
editing.
• For stereo samples, the display will indicate “Save to
No.(L)” and “(R).” These respectively specify the
writing-destination sample numbers for the L and R
channels.
• If you Copy a mono sample into the buffer, and then
Insert , Mix , or Paste it to a stereo sample, the data will
be inserted, mixed, or pasted into both the L and R sides.
(The result is that a stereo sample will be created.)
If you
Copy a stereo sample into the buffer, and then
Insert , Mix , or Paste it to a mono sample, the L- and R-
side data in the buffer will be mixed to mono, and then
inserted, mixed, or pasted. (The result is that a mono
sample will be created.)
You can also use these commands if you wish to mono-
mix a stereo sample and use it as a mono sample.
However, be aware that once a sample has been mixed to
mono, it is no longer possible to return it to a stereo
sample.
Start and End settings
When using the Sample Edit, Truncate – “Volume Ramp”
and the Loop Edit, Truncate to edit the waveform data of a
sample, you must first use Start and End to specify the
region that you want to edit, and then select and execute a
page menu command.
There is no compare function that lets you return the
edited result to the state before editing. If you wish to
preserve the unedited sample, uncheck the
Overwrite
*1
item in the dialog box of each page menu command
before you execute.
Note: To edit the Start , Loop Start , or End points, use Loop
Edit.
If the above parameters are located within an area of sample
addresses that are deleted or moved by your editing, they
will automatically be moved.
The Loop Start and End (2–1d) must be at least eight
samples apart. If you try to use the Truncate , Cut , or
Rate Convert commands, but the results of the
commands would cause the Loop Start and End to be
separated by less than eight samples, you’ll see the error
message “Sample length is shorter than minimum.”
Please set the
Start and End appropriately.
About Overwrite
When Overwrite is unchecked : When the command is
executed, the edited sample will be saved in a different
sample number. The unedited sample will remain without
change.
When Overwrite is checked : When the command is
executed, the edited sample will be overwritten onto the
original sample (number). The original sample will be
modified.