Korg NAUTILUS Series, Руководство по параметрам, Страница: 132 / 961

PROGRAM mode: HD-1
122
Swap Scene
This command swaps (exchanges) the settings of two
SCENE 1-4 buttons.
1. Choose “Swap Scene” to open the dialog box.
2. In “Source1” and “Source2”, select two ARP Scenes.
that you wish to swap.
3. To execute the swap, press the OK button. To cancel
without executing, press the Cancel button.
Initialize Scene
This initializes the settings of a scene.
1. Select “Initialize Scene” to open the dialog box.
2. Select the scene you wish to initialize.
3. Press the OK button to initialize, or press the Cancel
button if you decide not to initialize.
Copy Insert Effect
Copy Insert Effect is available on all of the IFX pages.
This command copies effects settings from within the
current Program, from other Programs, Combinations, or
Songs, or from the current SAMPLING mode settings.
1. Select “Copy Insert Effect” to open the dialog box.
2. Select the mode, bank and number of the copy source
in “From”.
When you press the “Set To Current” button, the
currently selected mode, bank, number and IFX (edit cell)
will automatically be assigned to “From”. This is useful
when you want to temporarily copy an IFX that was
already configured to an open effect slot, such as when
you want to try out different effect settings.
3. Select the effect to copy. You can also copy from the
master effect or the total effect.
All:
All settings of the insert effect (the contents of the
Insert FX page and the IFX1–12 effect parameters,
excluding the “Ctrl Ch”) will be copied.
All used: Only the insert effects currently used will be
copied from IFX1–12 of the copy source.
The copy source will be copied to consecutive open slots
(from “000: No Effect”—note that the contents of the
chain are not included), beginning with the insert effect
set in “To:”.
Note: The insert effect in the copy source that is set to
“000: No Effect” will not be copied. However, it will be
copied if “000: No Effect” is included in the chain. (Note
that if the chain in the copy source contains only “000:
No Effect”, the insert effect will not be copied.)
4. Select the insert effect in the copy destination.
Select the “Post IFX Mixer Setting” checkbox to
simultaneously copy the settings after the signal passes
through the insert effects in the copy source, namely “Pan
(CC#8)”, “Bus Sel.”, “Ctrl Bus”, “REC Bus”, “Send1”
and “Send2”. If this is left cleared, only the effect type
and parameters will be copied.
5. Press the OK button to copy the insert effect, or press
the Cancel button to quit.
If you have copied from the master effect, the resulting
effect will not be the same as the master effect, due to
differences in routing and level settings in the master
effect.
Swap Insert Effect
Swap Insert Effect is available on all of the IFX pages.
This command exchanges the effects, and their internal
parameters, between two IFX slots.
All of the parameters shown on the IFX 1-12 pages will be
copied.
Other IFX slot parameters will not be affected, including
Pan, Sends 1 and 2, Chain, REC Bus, and FX Control Bus.
1. Select “Swap Insert Effect” to open the dialog box.
2. In “Source 1” and “Source 2,” select each of the insert
effects that you wish to swap.
3. To execute the Swap Insert Effect command, press the
OK button. To cancel, press the Cancel button.
Insert IFX Slot
Insert IFX Slot is available on the Routing and Insert FX
tabs of the IFX page.
This command inserts an IFX slot.
Slots located after the inserted location will be relocated
downward if a vacant slot exists. At this time,
Chain , Pan
(CC#8) , REC Bus , FX Control Bus , Send 1/2 , and Ctrl Ch
(only for Combi and SEQ) will also be relocated.