background image

6

Major Component Replacements

KXHE60A

K2XHE60A

Fan Motor Assembly

0265-09

0265-10

Heat Exchanger Element

0744-19A

0744-19A

Filter

5001F

5001F

Above parts are for 115V units.  For 230V, consult factory.

VII. Maintenance

Kooltronic Air-Cooled Heat Exchangers are designed to require only routine cleaning
of air filters and the heat exchanger element to assure unimpeded airflow through the
heat exchanger element.  It is not possible to recommend specific filter cleaning
intervals since the level and the nature of air borne particulate matter differs widely
with each installation.  It is generally sufficient to remove and wash the reusable alu-
minum mesh air filter when the outer surface of these filters appear covered with a thin
layer of dust or lint.  Filter recoating adhesive is recommended. Appropriate dis-
posable filters are available from Kooltronic.

If filter service is neglected or delayed, the heat exchanger will not perform at its design
capacity. The first indication of excessively clogged air filter is usually a gradual
increase of temperature within the equipment cabinet.  Continued operation under
these conditions will cause damage, shorten blower motor life and void the warranty.

Filter Removal and Service

Kooltronic Heat Exchanger feature an easily removable inlet filter to
facilitate necessary cleaning.

CAUTION

Do not operate the Heat Exchanger for extended periods

of time with the filter removed.  The heat exchanger element

may become clogged with dust or lint from the ambient

environment.  A clogged heat exchanger element is not 

readily detected and will give the same reaction as clogged

filter.  A clean filter is the best protection.

CAUTION

Disconnect electric power from the Heat Exchanger

before proceeding.

Содержание KXHE60A









Отзывы: